KAESER M100 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 384

KAESER M100 Скачать руководство пользователя страница 42

➤ The towbar must be parallel with the ground otherwise towing instability can develop, resulting

in damage to the machine and/or towing vehicle.

➤ Before moving the machine, make sure any security devices (e.g. anti-theft chain) are re‐

leased.

Transport as trailer on public roads

➤ Do not tow machines without service brake on public roads.
➤ Do not tow machines without illumination and signaling equipment on public roads.
➤ Ensure all running gear, including chassis, wheels, brakes, signalling and lighting, is in safe

condition.

➤ The local laws and regulations regarding the use of public roads must be observed.

Transporting with a crane

Non-compliance with the safety regulations for load suspension and hoisting equipment may cause

severe accidents during lifting and moving the machine with cranes.
➤ Do not enter the danger zone while the machine is being lifted.
➤ Never lift and move the machine over people or occupied buildings.
➤ Avoid extreme weight shifting caused by additional loads or additions (tilting).
➤ Do not exceed the lifting capacity on the machine's lifting point (lifting eye).
➤ Only the designated lifting point should be used to attach lifting gear and under no circumstan‐

ces are handles, tow-bar or other components to be used.

➤ Use only hooks and shackles that comply with local safety regulations
➤ Do not attach cables, chains or ropes directly to the machine's lifting eye.
➤ Do not manipulate the crane suspension system, in particular the holding points of the crane

lifting eye.

➤ If screwed crane fixings had to be removed, please use only new self-locking nuts when instal‐

ling.

➤ Avoid jerking when lifting, as this may damage components.
➤ Loads must be slowly lifted and carefully set down.
➤ Never allow the load to hang from the crane longer than necessary.

The following are forbidden:

■ Air transport of the machine by slinging beneath a helicopter.
■ Dropping the machine by parachute.

3.5.2.2 Installation

The operator must ensure that only authorised personnel has access to the machine.

General instructions

A suitable installation location for the machine prevents accidents and faults.
➤ Do not position the machine directly against a wall. A build up of heat from the exhaust can

damage the machine.

➤ Ensure accessibility so that all work on the machine can be carried out without danger or hin‐

drance.

3

Safety and Responsibility

3.5

Dangers

30

Operator Manual Screw Compressor
M100

No.: 9_6999 23 USE

«
...
40
41
42
43
44
...
»

Содержание M100

































































































































































































































































































































































































Отзывы:

Нет отзывов