KAESER M100 Скачать руководство пользователя страница 144 | Manualshive

Страница: 144 / 384

background image

10.4.2 Cooling oil filling and topping up

Material Cooling oil

Funnel
Cleaning cloth
Wrench

Precondition The machine is shut down.

The machine is standing level.
The machine is fully vented, the pressure gauge reads 0 psig.
Machine is cooled down.
All compressed air consumers are disconnected and the air outlet valves are open.
The negative cable to the battery is disconnected.

Filling with cooling oil

A sticker on the oil separator tank specifies the type of oil used.
1.

The machine could be damaged by unsuitable oil.

➤ Never mix different types of oil.
➤ Never top up with a different type of oil than that already used in the machine.

2. Open the right-hand access door.
3. Slowly unscrew and withdraw the plug from the oil filler port.
4. Top up the cooling oil to the maximum level

B

with the help of a funnel.

5. Check the oil level.
6. Check the filler plug gasket for damage.

Change a damaged gasket.

7. Replace the plug in the filler port.
8. Reconnect the negative battery terminal.
9. Close the access door.

Starting the machine and performing a test run:

1. Start the machine and run in IDLE until the operating temperature is reached.
2. Close the outlet valves.
3. Shut down the machine.
4. Wait until the machine has automatically vented.

Pressure gauge reads 0 psig!

5. Open the outlet valves.
6. Open the right-hand access door.
7. Check the oil level after about 5 minutes.

Top up if necessary.

8. Visually inspect for leaks.
9. Close the access door.

10 Maintenance

10.4 Compressor Maintenance

132

Operator Manual Screw Compressor
M100

No.: 9_6999 23 USE

«
...
142
143
144
145
146
...
»

Содержание M100

































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M100

Бренд: Danfoss Страницы: 2

Бренд: Gardner Denver Страницы: 58

Бренд: DMEGA Страницы: 16

Бренд: Hitachi Страницы: 44

Highly WHP13300PSD

Бренд: Hitachi Страницы: 33

HISCREW V PLUS NEXT Series

Бренд: Hitachi Страницы: 72

HISCREW 2000 Series

Бренд: Hitachi Страницы: 72

Бренд: Kobalt Страницы: 84

Бренд: Powerex Страницы: 12

Бренд: Shift3 Страницы: 16

Бренд: Doss Страницы: 4

Бренд: California Air Tools Страницы: 15

Бренд: Atlas Copco Страницы: 40

Бренд: WilTec Страницы: 12

Бренд: RIDGE RYDER Страницы: 2

InTouch HA12P/110-4

Бренд: GEA Страницы: 26

Бренд: GEA Bock Страницы: 32

Бренд: Proheat Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды