KAESER M100 Скачать руководство пользователя страница 114

Страница: 114 / 384

10.2.3.1 Machine maintenance schedule

➤ Carry out maintenance tasks according to the following schedule.

Component
Function

Daily

A250

A500

A1000

A1500

A2000

A3000

A36000

See chapter

Note

Engine
Check inlet air filter mainte‐

nance indicator

10.3.2

Check engine oil level.

10.3.4

Engine

Clean the engine air filter

10.3.2

Change the engine oil

10.3.6

Replace the engine oil filter.

10.3.7

Engine

Check/adjust the drive belt ten‐

sion.

10.3.8

Engine

Replace the drive belt.

10.3.8

Engine

Change engine air filter.

10.3.2

Have the valve clearance adjus‐

ted.

Engine

Have the turbocharger checked.

Check the engine coolant level.

10.3.1

Engine

Clean the cooler.

10.5

Check antifreeze concentration.

10.3.1

Engine

Check radiator hose and hose

clips, have replaced if necessa‐

ry.

Engine

Change the coolant.

10.3.1

Engine

Fill up the fuel tank

Check/empty the water trap.

10.3.3

Check fuel lines and hose

clamping bands, have replaced

if necessary.

Have fuel lines and clamps re‐

placed.

Engine SM = engine manufacturer's service manual; SW = specialized workshop.

10 Maintenance

10.2 Maintenance schedules

102

Operator Manual Screw Compressor
M100

No.: 9_6999 23 USE

Содержание M100

































































































































































































































































































































































































Результаты поиска

Содержание M100

Отзывы:

Похожие инструкции для M100

Бренды по названию

Популярные бренды

KAESER M100, Руководство оператора

Результаты поиска

Содержание M100

Отзывы:

Похожие инструкции для M100

Бренды по названию

Популярные бренды