KAESER M100 Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 384

KAESER M100 Скачать руководство пользователя страница 130

4. Mount the micro-filter cartridges on the filter mount:

■ Moisten the rubber seals of the filter mount and the sealing faces of the new filter cartridge

with some fuel.

■ Manually screw the filter cartridge to the filter head (clockwise), until seal is tight.

5. Reconnect the battery.
6. Close the door.

The fuel system must be bled after the filter cartridges have been changed.

Dispose of fuel and any materials and components contaminated with it in accordance with

environmental protection regulations.

Starting the machine and performing a test run:

1. Switch the machine on and run it in IDLE mode for approx. 1 minute.
2. Shut down the machine.
3. Open the right-hand access door.
4. Visually check the fuel system for leaks.
5. Tighten all fittings.
6. Close the door.

Further information The engine service manual provides further information on fuel system maintenance.

10.3.4 Checking the engine oil level

The engine oil is indicated by a dipstick in the oil sump. The oil level should ideally be between the

two marks on the dipstick. The oil level should not be allowed to fall below the

minimum level.

Material Cleaning cloth

Precondition The machine is shut down.

The machine is standing level.
The machine is fully vented, the pressure gauge reads 0 psig.
Engine cooled down.
All compressed air consumers are disconnected and the air outlet valves are open.

10 Maintenance

10.3 Engine maintenance

118

Operator Manual Screw Compressor
M100

No.: 9_6999 23 USE

«
...
128
129
130
131
132
...
»

Содержание M100

































































































































































































































































































































































































Отзывы:

Нет отзывов