KAESER M100 Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 384

background image

10.3 Engine maintenance

➤ Perform maintenance tasks according to the schedule in chapter 10.2.3.1.

10.3.1 Water cooler maintenance

Material Coolant

Coolant tester
Oil receptacle
Drain hose with hose coupling is disconnectedly laying at the machine
Funnel
Cleaning cloths

Precondition The machine is switched off.

The machine is standing level.
The machine is fully vented, the pressure gauge reads 0 psig.
The machine has cooled down.
All compressed air consumers are disconnected and the air outlet valves are open.

Danger of scalding by hot coolant!

Serious injuries can be caused by hot coolant.
➤ Let the machine cool down before opening the cooling system.

Risk of chemical burns from coolant containing antifreeze!
➤ Avoid eye and skin contact with coolant. If the eyes are affected, rinse immediately with

running water.

➤ Wear protective glasses and gloves.

Insufficient coolant can damage the engine.

Insufficient coolant will cause the engine to overheat. Overheating can cause serious dam‐

age to the engine.
➤ Check the coolant level daily.
➤ Top up the coolant as necessary.

➤ Open the right-hand access door.

10.3.1.1 Checking coolant level

The coolant level in the engine cooling circuit must be checked daily prior to startup.
The level is checked on the coolant expansion tank.

■ The tank is semi-transparent so the coolant level can be seen from outside.
■ The level should be between the

minimum and maximum markings when the engine has

cooled down.

10 Maintenance

10.3 Engine maintenance

106

Operator Manual Screw Compressor
M100

No.: 9_6999 23 USE

«
...
116
117
118
119
120
...
»

Содержание M100

































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M100

Бренд: Central Pneumatic Страницы: 20

Бренд: Mitsubishi Страницы: 3

Copeland Stream 4MA-22X

Бренд: Emerson Страницы: 28

Copeland Scroll ZPD103

Бренд: Emerson Страницы: 19

Copeland Scroll ZR K3 Series

Бренд: Emerson Страницы: 18

Copeland Stream Digital 4MAD-22X

Бренд: Emerson Страницы: 31

Copeland Scroll ZR108KRE

Бренд: Emerson Страницы: 40

Copeland Scroll ZP23K Series

Бренд: Emerson Страницы: 24

Copeland Scroll ZR24KRE

Бренд: Emerson Страницы: 28

Copeland Scroll ZP KC Series

Бренд: Emerson Страницы: 32

Copeland Scroll ZS KAE Series

Бренд: Emerson Страницы: 16

Бренд: DeWalt Страницы: 46

Бренд: DeWalt Страницы: 55

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 3

Бренд: Sealey Страницы: 4

Бренд: Sealey Страницы: 4

SAC5020E110V.V2

Бренд: Sealey Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды