JVC GY-HM790U, Инструкция по эксплуатации

Страница: 18 / 144

14
Introduction
Side Terminal
A
[Y/VIDEO] Y/Composite Video Signal Output
Terminal (BNC) ( A Page 122)
B
[PB] PB Video Signal Output Terminal (BNC)
( A Page 122)
C
[GENLOCK/AUX] Genlock/AUX Selection Switch
(U model only) ( A Page 125)
D
[GENLOCK/AUX IN] Genlock/AUX Input Terminal
(U model)/[GENLOCK INPUT] Genlock Input Terminal
(E model)
U model : For input of external synchronizing signals or
external composite video signals.
(
A
Page 125 [Input of Composite Video Signals
from External Device (GY-HM790CHU/GY-
HM790U only)])
E model : For input of external synchronizing signals.
( A Page 126 [Input of External Synchronizing
Signal (Genlock)])
E
[TC IN] Time Code Input Terminal (BNC)
( A Page 4 8 to 52)
F
[TC OUT] Time Code Output Terminal (BNC)
( A Page 4 8 to 52)
G
[STUDIO] Studio Terminal (10-pin) (
A
Page 12 8 )
Connect to this terminal when combining the use of products,
such as a transmission unit, from a different manufacturer.
H
[PR] PR Video Signal Output Terminal (BNC)
(
A
Page 122)
I
[DC INPUT] DC Input Terminal (
A
Page 22)
Input terminal for DC 12 V power supply. Connects with an
AC adapter.
J
[REMOTE] Remote Terminal (
A
Page 1 3 1)
K
[HD/SD-SDI] HD/SD-SDI Output Terminal (BNC)
(
A
Page 122)
L
[AUDIO OUTPUT CH-1/CH-2] Audio Output Terminal
(RCA)
Output terminal for audio signals.
●
Input audio signals are output during Camera mode.
●
Playback audio signals are output during Media mode.
●
Audio from input audio signals is output during HD/DV signal
(IEEE1
3 94) input.
Memo :
●
Alarm tone is not output.
M
[INT/EXT] IEEE1 3 94 Interface Terminal Switch
( A Page 12 3 )
For selecting a valid IEEE1 3 94 interface terminal.
N
Shoulder Pad Slide Button
For adjusting the shoulder pad position. Press this button to
adjust the shoulder pad
O
position to the front or back.
O
Shoulder Pad
P
[USB] USB Terminal ( A Page 1 3 0)
Q
[IEEE1 3 94] IEEE1 3 94 Terminal (4-pin)
For connecting digital video e q uipment with IEEE1 3 94
terminal using an IEEE1 3 94 cable (sold separately).
To enable this terminal, set the [INT/EXT] IEEE1 3 94 terminal
switch
M
to [EXT].
( A Page 12 3 [IEEE1 3 94 Connection])
Note :
●
When connecting IEEE1 3 94 cables, check that the
connectors are facing the right direction before you insert.
Memo :
●
Put on the covers when the connectors are not in use.
Names of Parts (continued)
Pin No. Signal
Input/
Output
1 NC ^
2 CALL TALLY IN
3 RM TALLY OUT
4 RM PREVIEW OUT
5 NC
^
6 NC ^
7 TALLY IN IN
8 RETURN GND
^
9 RETURN IN IN
10 GND ^
K L M N O
P
Q
I H
C
A
D
E
F
G
J
B
[EXT]
:
Enables IEEE1 3 94 signals from the [IEEE1 3 94]
terminal
Q
.
[INT]
:
Enables the accessory connector
B
at the rear
of the camera recorder. ( A Page 15)