JCM GLOBAL UBA Pro Series, Руководство по эксплуатации и обслуживанию

Страница: 126 / 132

Appendix A UBA™ Pro Series Universal Banknote Acceptor Troubleshooting
P/N 960-000211R_Rev. A © 2020, JAPAN CASH MACHINE CO., LTD.
A - 1 2
Position Sensor
00-00-02
Calibration Program
process failed.
•
Check that a correct Reference Paper is placed in a
proper direction. (Refer to “Placing Reference Paper”
on page 6-5.)
•
Check that a Reference Paper is not damaged or dirty.
(Refer “Reference Paper Handling” on page A-14.)
•
Check that the relative part is properly assembled and/
or Harness are connected.
•
Clean the relative Sensor. (Refer to “Cleaning
Procedure” on page 2-17.)
•
Position Sensor
Anti-Pullback
Entrance Sensor
00-00-04
Calibration Program
process failed.
•
Check that a correct Reference Paper is placed in a
proper direction. (Refer to “Placing Reference Paper”
on page 6-5.)
•
Check that a Reference Paper is not damaged or dirty.
(Refer “Reference Paper Handling” on page A-14.)
•
Check that the relative part is properly assembled and/
or Harness are connected.
•
Clean the relative Sensor. (Refer to “Cleaning
Procedure” on page 2-17.)
•
Anti-Pullback
Entrance Sensor
Exit Sensor 2
00-00-08
Calibration Program
process failed.
•
Check that a correct Reference Paper is placed in a
proper direction. (Refer to “Placing Reference Paper”
on page 6-5.)
•
Check that a Reference Paper is not damaged or dirty.
(Refer “Reference Paper Handling” on page A-14.)
•
Check that the relative part is properly assembled and/
or Harness are connected.
•
Clean the relative Sensor. (Refer to “Cleaning
Procedure” on page 2-17.)
•
Exit Sensor 2
Exit Sensor 1
00-00-10
Calibration Program
process failed.
•
Check that a correct Reference Paper is placed in a
proper direction. (Refer to “Placing Reference Paper”
on page 6-5.)
•
Check that a Reference Paper is not damaged or dirty.
(Refer “Reference Paper Handling” on page A-14.)
•
Check that the relative part is properly assembled and/
or Harness are connected.
•
Clean the relative Sensor. (Refer to “Cleaning
Procedure” on page 2-17.)
•
Exit Sensor 1
EEPROM Read Error
00-01-00
EEPROM reading
and/or saving was not
properly performed.
•
Perform the Sensor Calibration procedure.
•
Check that the relative part is properly assembled and/
or Harness are connected.
•
Clean the relative Sensor. (Refer to “Cleaning
Procedure” on page 2-17.)
•
CPU Circuit Board
EEPROM Write Error
00-02-00
EEPROM writing and/
or saving was not
properly performed.
•
Perform the Sensor Calibration procedure.
•
Check that the relative part is properly assembled and/
or Harness are connected.
•
Clean the relative Sensor. (Refer to “Cleaning
Procedure” on page 2-17.)
•
CPU Circuit Board
EEPROM Error
00-04-00
EEPROM reading,
writing and/or saving
was not properly
performed.
•
Perform the Sensor Calibration procedure.
•
Check that the relative part is properly assembled and/
or Harness are connected.
•
Clean the relative Sensor. (Refer to “Cleaning
Procedure” on page 2-17.)
•
CPU Circuit Board
00-08-00
EEPROM reading,
writing and/or saving
was not properly
performed.
•
Perform the Sensor Calibration procedure.
•
Check that the relative part is properly assembled and/
or Harness are connected.
•
Clean the relative Sensor. (Refer to “Cleaning
Procedure” on page 2-17.)
•
CPU Circuit Board
Table A-9 Position Sensor Calibration Error Codes (Continued)
Sensor/Error Error Code Solutions
Relative
Parts/Sensors