janitza UMG 96S Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 96

background image

Page 25

Check measurement

If all voltage and current inputs are connected
correctly, the single phase and sum power must
be calculated and indicated correctly.

Check single phase power

If a current transformer is assigned to the wrong
outer  conductor,  the  corresponding  power  is
measured incorrectly.
The assignment of the outer conductor and ct at
UMG96S  is  correct,  when  there  is  no  voltage
between outer conductor and the corresponding
ct (primary).
To ensure the outer conductor is assigned to the
right  ct,  the  ct  can  be  short-circuited  at  the
secondary. The UMG96S must indicate the cor-
responding  apparent  power  in  this  phase  with
zero.

If the apparent power is indicated correctly, but
the real power is indicated negatively, the ct ter-
minal has been exchanged or power is supplied
to the energy supplier (generator).

Check sum power

If all voltage, current and power are indicated
correctly, the sum power must be indicated cor-
rectly as well. As confirmation, please compare
the indicated sum power of UMG96S with other
meters, that might be available.

Connect measurement current

The UMG96S is designed for the connection of
../1A and ../5A current transformers.
Only alternating currents can be measured, no
direct currents
.

Current transformer terminals must be
earthed on the secondary.
Current transformers, which do not carry
load on the secondary, can lead live
voltage and must be short-circuited.

Please connect the current inputs one after the
other  and  compare  the  indicated  current  with
the  real  current.  Please  remember,  that  the  ct
ratio is set to 5/5A and must be adapted to the
used cts.
If  the  current  transformer  is  short-circuited  on
the secondary, the UMG96S must indicate zero
A in the corresponding outer conductor.
The current, indicated by UMG96S must corre-
spond  to  the  input  current  with  respect  to  the
current transformer.

Check current direction

Short-circuit two current transformers. The re-
maining phase must display real power as:
(+) for consumption of real power or
(-) for supply of real power (generator).
If no real power is indicated, the assignment of
voltage to current may be false.

Check phase assignment

The  assignment  outer  conductor  to  current
transformer  is  correct,  when  the  indicated  cur-
rent  in  UMG96S  gets  0A  while  short-circuiting
the secondary of the current transformer.

c

RS 232

RS 485 I / O

UMG96 S
45-65Hz 3VA
Made in Germany
S V J M A D E P

Strommessung/Current Measurement

k
l

L2

L3

L1

k
l

k
l

5

7

10

8

9

N L3 L2 L1

6

Spannungsmessung
Voltage Measurement

15 14 13 12 11 4 3 2 1

Profibus

«
...
23
24
25
26
27
...
»

Содержание UMG 96S

































































































Отзывы:

Нет отзывов

Похожие инструкции для UMG 96S

DigitalFlow GF868

Бренд: GE Страницы: 80

Бренд: 3nh Страницы: 10

Бренд: ECO Sensors Страницы: 22

Бренд: ECO Sensors Страницы: 7

Бренд: F&F Страницы: 24

Бренд: Kamstrup Страницы: 100

Бренд: Kamstrup Страницы: 16

Бренд: Kamstrup Страницы: 12

Бренд: Kamstrup Страницы: 60

Бренд: Kamstrup Страницы: 136

Бренд: Kamstrup Страницы: 16

Бренд: Kamstrup Страницы: 155

Бренд: Landis+Gyr Страницы: 26

Бренд: Landis+Gyr Страницы: 3

Бренд: NanoEnTek Страницы: 4

Бренд: Omano Страницы: 14

Бренд: PASCO Страницы: 3

Бренд: PASCO Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды