janitza UMG 96S Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 96

background image

Page 19

Sum current measurement

If the current measurement is carried out via two
current transformers and a sum current trans-
former, the total transformer ratio must be
programmed at UMG96S.

Example: Sum current transformer
A current measurement is carried out via one ct
with a ratio of 1000/5A and one ct with a ratio of
1000/5A. The current measurement is carried
out via a sum current transformer 5+5/5A.
The UMG96S must be programmed as follows:
Primary current: 1000A + 1000A =

2000A

Secondary current:

5A

Verbraucher 1

Consumer 1

Verbraucher 1

Consumer 1

Einspeisung 1

Supply 1

Einspeisung 1

Supply 1

UMG96S

L l

K k

L l

K k

AK AL

K l

k l

BK Bl

Current measurement

The current measurement is carried out via cur-
rent transformers of either ../5A or ../1A. If the
current must be measured by an Amperemeter
additionally, it must be connected in series to the
UMG96S.
In networks with voltage up to 150VAC against
ground, currents up to 5A can be connected di-
rectly to the UMG96S.

L l

K k

A

l

k

UMG96S

Verbraucher

Consumer

Einspeisung

Supply

Attention!

The secondary connections of the current
transformer  must  be  short-circuited,  be-
fore the wires that lead to the device are
interrupted!
If a testing switch is available, which short-
circuits  the  secondaries  of  the  cts  auto-
matically, it is sufficient to set it into posi-
tion  "check",  provided  that  the  short-
circuiters have been checked before.

m

«
...
17
18
19
20
21
...
»

Содержание UMG 96S

































































































Отзывы:

Нет отзывов

Похожие инструкции для UMG 96S

Masoneilan 12400 Series

Бренд: Baker Hughes Страницы: 81

Бренд: BANTE inststruments Страницы: 15

Бренд: 3Bays Страницы: 21

Бренд: Omano Страницы: 14

Бренд: velocomp Страницы: 4

Prestige Series

Бренд: Ibanez Страницы: 54

Бренд: CONDTROL Страницы: 8

Бренд: Bahco Страницы: 21

Бренд: Kübler Страницы: 72

Бренд: Integra Страницы: 32

Бренд: DAPAudio Страницы: 8

Celviano AP-500

Бренд: Casio Страницы: 2

Бренд: Velleman Страницы: 18

Бренд: Kawai Страницы: 56

Бренд: Bluther Страницы: 24

Бренд: ATIM Страницы: 32

Бренд: Kobold Страницы: 27

Бренд: Hanna Instruments Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды