janitza UMG 96S Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 96

background image

Page 69

Measured value (Addr. 015)

The measured value indicates the address of
the supervised measured value. The following
values can be assigned:
000 = Comparator inactive.
001 = the comparator result can be written
externally (Modbus RTU).
200 ..

400 = Measured values of measured

value list.

Limit (Addr. 018)

The limit serves a constant of the type LONG.
The limit is compared to the corresponding
measured value.

Minimum time (Addr. 016)

For the duration of the minimum time, the com-
parator result remains active (Addr.389). The
minimum time can be programmed in the range
of 1...900 seconds.

Run up time (Addr. 064)

At  least  for  the  duration  of  the  run  up  time,  a
violation  of  the  limit  must  be  active  to  change
the comparator result.
The  run  up  time  can  be  programmed  in  the
range of 1...900 seconds.

Diagr. Example, Limit violation.

Minimum time

t

Limit

Measured

value

Exceeding

t

Comparator result

t

2 seconds

t

run up time

t

2 Seconds

Operator (Addr. 017)

There are two operators available for the
comparsion of measured value and limit.
Operator =

0

means

higher than (>=)

Operator =

1

means

smaller than (<)

Comparator result (Addr.386)

The result of the comparison of measured value
and limit is the comparator result.
The correspondence is:
0 = No limit violation.
1 = Limit violation.

Data memory (Addr. 500)

Changes of the comparator results can be
stored in the memory (option), as long as profile
4 for the memory (addr. 056) was activated.

Total running time (Addr. 396)

This is the sum of all times, for which the limit
was violated.

Combination (Addr. 044)

Combines the results of the comparators A, B
and C

AND

or

OR

.

Invert result (Addr. 046)

The result of the combination (Addr. 046) can be
inverted or not.

Total combination result (Addr. 389)

The combined comparator results of the com-
parators A, B and C are in the total combination
result.

«
...
67
68
69
70
71
...
»

Содержание UMG 96S

































































































Отзывы:

Нет отзывов

Похожие инструкции для UMG 96S

Бренд: Kawai Страницы: 70

Бренд: E+E Elektronik Страницы: 40

Бренд: LATNEX Страницы: 55

Бренд: Laser Technology Страницы: 11

Бренд: Laser Technology Страницы: 62

NANOCOLOR UV/VIS II

Бренд: Macherey-Nagel Страницы: 99

Бренд: MULTISPAN Страницы: 2

Бренд: SOMFY Страницы: 40

Бренд: Fly Henry Страницы: 5

DT4120 PS Series

Бренд: Datcon Страницы: 92

Бренд: TAC Страницы: 28

Бренд: Hanna Instruments Страницы: 2

Бренд: Vogel Страницы: 4

K-PATENTS PR-23 AX Series

Бренд: Vaisala Страницы: 246

Бренд: MFJ Страницы: 5

Бренд: ATIM Страницы: 25

Бренд: OrienTek Страницы: 2

Бренд: BIRD Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды