janitza UMG 96S Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 96

background image

Page 9

Voltage versions

The  UMG96S  takes  the  measurement  voltage
as operating voltage and can be delivered in the
versions 150V and 300V. The delivered version
is  indicated  on  the  type  plate  of  UMG96S.
Please  ensure,  that  the  local  net  conditions
match  the  numbers  on  type  plate  before  con-
nection.

300V standard version

In

300V standard version

, the UMG96S can

measure voltage up to 300VAC against ground.
At leats one phase (L) of the UMG96S and the
neutral N must be connected and the connected
voltage must be within the measurement and
operation voltage range.
The

measurement and operation voltage

range

of devices without additional PCB and for

devices with additional PCB 1 (analogue output)
are:
Measuring range L-N

: 50 .. 300V AC

Measuring range L-L

: 87 .. 520V AC

Operating voltage range L-N

: 85 .. 300V AC

The measurement and operating voltage range
for devices with additional PCB 2 (Profibus) are:
Measuring range L-N

: 50 .. 300V AC

Measuring range L-L

: 87 .. 520V AC

Operating voltage range L-N

:140.. 300V AC

150V special version

In

150V special version,

the UMG96S can

measure voltage up to 300VAC against ground.
At least 2 phases (L) of the UMG96S must be
connected, and the connected voltage must be
within the measurement and operation voltage
range.

Measuring range L-N

: 25 .. 140V AC

Measuring range L-L

: 40 .. 260V AC

Operating voltage range L-L

: 85 .. 260V AC

Attention!

Voltage, which is above the allowed
range can damage the device.

m

The operating voltage for the unit is taken
from the outer conductors.

m

«
...
7
8
9
10
11
...
»

Содержание UMG 96S

































































































Отзывы:

Нет отзывов

Похожие инструкции для UMG 96S

Бренд: Raytech Страницы: 18

Бренд: Olympus Страницы: 4

Бренд: DGH Страницы: 87

Бренд: HBM Страницы: 84

Бренд: Armstrong Monitoring Corporation Страницы: 12

Бренд: Veeco Страницы: 349

Бренд: GrainPro Страницы: 7

Бренд: Caen Страницы: 50

Бренд: Interacoustics Страницы: 54

Бренд: PCB Piezotronics Страницы: 10

Бренд: J&D Electronics Страницы: 2

Intelligizer Fence Monitor

Бренд: Zareba Страницы: 8

Бренд: SEFRAM Страницы: 31

Бренд: Rubicson Страницы: 4

Бренд: Hanna Instruments Страницы: 2

Бренд: RX Страницы: 8

SensoControl ServiceJunior

Бренд: Parker Страницы: 18

Бренд: Azbil Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды