janitza UMG 96S Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 96

background image

Page 63

Minimum pulse duration (Addr. 010)

The  minimum  pulse  duration  can  be  pro-
grammed  on  10  ms  steps  in  a  range  between
50ms  and  1000ms. The  shortest  pulse  pause
corresponds to the programmed minimum pulse
duration.
At a minimum pulse duration of 50ms the maxi-
mum  pulse  frequency  is  10Hz.  If  less  pulses
must be transmitted, the pulse pause becomes
longer. The  programmed  minimum  pulse  dura-
tion of 50ms remains constantly.

Attention!

When the real energy meter with

reverse

running stop

works, pulses are only

given out while consumption of energy.
As the reactive energy meter works with

reverse running stop,

pulses are only

transmitted at inductive load.

Attention!

The pulse pause is not proportional to
power.

m

m

Diagr. Maximum pulse frequency at minimum
pulse duration of 50ms.

Impuls

50ms

Pulse pause

50ms

100ms => 10Hz

Minimum pulse duration

Pulse pause

Minimum pulse duration

Impuls

0.05s

Diagr. Pulse frequency <10Hz at minimum pulse
duration of 50ms.

Pulse valence

The pulse valence tells you, how much energy
is related to one pulse (Wh or kvarh).

The pulse valence may not be confused with the
meter constant. The meter constant is given in

Meter constant = rotations per kWh

The correspondance between pulse valence
and meter constant can be seen in the following
relations:

Meter constant = 1 / pulse valence

Pulse valence = 1 / meter constant

Pulse valence =

energy

max. pulse frequency 3600s

Pulse fr

∗

e

equency in Wh/pulse

Energy at Wh
Max. puls frequency at Hz

Attention!

The apparent energy cannot be transmit-
ted via puls output.

m

«
...
61
62
63
64
65
...
»

Содержание UMG 96S

































































































Отзывы:

Нет отзывов

Похожие инструкции для UMG 96S

Бренд: Yamaha Страницы: 2

Бренд: Daewoo Страницы: 2

Бренд: E+E Elektronik Страницы: 40

Бренд: ICS Schneider Messtechnik Страницы: 40

Бренд: THORLABS Страницы: 21

Ocean Optics HR2000 Series

Бренд: Halma Страницы: 42

Бренд: Roland Страницы: 2

Micropilot S FMR533

Бренд: E+H Страницы: 12

Бренд: National Instruments Страницы: 169

Бренд: Parkside Страницы: 199

PHYSICS line C.A 832

Бренд: Chauvin Arnoux Страницы: 43

Бренд: LORECa Hearing Instrument Страницы: 43

Бренд: Extech Instruments Страницы: 8

Бренд: MFJ Страницы: 5

Бренд: R&S Страницы: 35

WattNode Plus WNC-3D-240-FT10

Бренд: CCS Страницы: 43

Бренд: OfiTE Страницы: 6

Бренд: Zamel Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды