janitza UMG 96S Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 96

janitza UMG 96S Скачать руководство пользователя страница 65

Page 65

3.) Determination of pulse valence

The energy, which is consumed within 1 hour
can be calculated as:

Energy = Real power * time

Energy = 400kW *1h

Energy = 400kWh

If a pulse valence of 400kWh per pulse is set,
the UMG96S transmits one pulse per hour at full
load, which corresponds to a pulse frequency of

= 1 pulse/h
= 1 pulse/3600Sec.
= 1/3600 Hz
= 0,00028 Hz

With this pulse valence, very few pulses are
transmitted. Supervision of energy in the range
of minutes is not possible.

But  UMG96S  can  provide  up  to  10  pulses  per
second  (10Hz),  and  the  data  collecting  device
can detect 50 pulses per second (50Hz). A pos-
sible  solution  is  to  programm  the  UMG96S  to
send  a  frequency  of  10Hz  at  400kW  (or  for
safety reasons 500kW).

= 500kWh

Energy per hour

= 500kWh / 3600
= 0,14kWh
= 140Wh

Energy per second

= 140Wh / 10
= 14Wh

Energy in 1/10 sec.

This means, if 10 pulses are sent per second
with a valence of 14Wh, this corresponds to the
power of 500kW for one hour.

Pulse valence

Addr. 004 = 14

Pulse valency =

500000Wh

10Hz 3600s

Pulse valency = 14Wh/P

∗

u

ulse

Pulse valence =

energy

max. pulse frequency 3600s

Pulse fr

∗

e

equency in Wh/pulse

Energy at Wh
Max. puls frequency at Hz

«
...
63
64
65
66
67
...
»

Содержание UMG 96S

































































































Отзывы:

Нет отзывов