janitza UMG 96S Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 96

background image

Page 6

Service

If you have problems, which are not described
in this manual, please ask our technical support.
For further handling of your questions, please
have the following on hand:
- Device description (see type plate),
- Serial number (see type plate),
- Software Release,
- Measurement and auxiliary voltage and
- Exact description of the problem.

You can contact us:
Monday to Thursday

between 07:00h and 15:00h

and Friday

between 07:00h and 12:00h

Janitza electronic GmbH
Vor dem Polstück 1
D-35633 Lahnau
Support:

Tel.

(0 64 41) 9642-22

Fax

(0 64 41) 9642-30

e-mail:

[email protected]

Hints for maintenance

Before  delivery  the  device  is  tested  in  various
safety  checks  and  marked  with  a  seal.  If  the
device  is  opened,  these  checks  must  be  re-
peated.
There  is  no  guarantee  for  devices,  which  are
opened out of the manufacturing works.

Repairing and calibration

Maintenance and calibration can only be carried
out at manufacturer's end.

Face plate

The cleaning of the front foil must be done with
a soft cloth using a common cleansing agent.
Acid or acidic agents may not be used for clean-
ing.

Battery

On  the  additional  PCB  1  (option),  there  is  a
Lithium battery. The life  expectance of the bat-
tery at storage tempe45°C is a minimum
of  5  years.  The  typical  life  expectance  is
between 8 and 10 years.
If the battery voltage is too low after net return,
the display shows the warning "Err 320".
For  safety  reasons,  the  battery  should  be  ex-
changed in the manufacturing works only!

Waste management

The UMG96S can be disposed and recycled as
electronical waste according to the legal regula-
tions. Please note, that the input Lithium battery
must be disposed separately.

«
...
4
5
6
7
8
...
»

Содержание UMG 96S

































































































Отзывы:

Нет отзывов

Похожие инструкции для UMG 96S

Бренд: TaiDoc Страницы: 31

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 16

Бренд: Bacharach Страницы: 19

Power Xpert PXM 4000

Бренд: Eaton Страницы: 28

Бренд: Oakton Страницы: 16

Бренд: Omicron Lab Страницы: 33

Бренд: Omicron Lab Страницы: 21

Бренд: Omicron Lab Страницы: 22

Бренд: Vectornav Страницы: 114

Бренд: Samsara Страницы: 16

KINGFISHER PLUS+

Бренд: semaphore Страницы: 247

Бренд: Hanna Instruments Страницы: 2

Бренд: Zero 88 Страницы: 32

Бренд: RS PRO Страницы: 41

Бренд: AEMC Страницы: 20

Бренд: Feasa Страницы: 145

Бренд: General Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды