janitza UMG 96S Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 96

background image

Page 46

Serial number (Addr. 911)

The serial number, which is indicated by the
UMG96S, is a 6 digit part of the serial number
on type plate.
The serial number cannot be changed.

Serial number on type plate

Indicated serial number

PRG

MkWh
MkVArh

L1

L2

L3

PRG

XX00-0000

Time detection

The UMG96S detects the operating hours of the
UMG96S, and the total running time of each
comparator. The time is measured with a solu-
tion of 0.1 hours, indicated in hours.
For the call up, the time is marked by the num-
bers 0 to 6:
0 = Operating hours counter (Addr.394)
1 = Total run. time, Comparator 1A (Addr.396)
2 = Total run. time, Comparator 2A (Addr.398)
3 = Total run. time, Comparator 1A (Addr.400)
4 = Total run. time, Comparator 2A (Addr.402)
5 = Total run. time, Comparator 1A (Addr.404)
6 = Total run. time, Comparator 2A (Addr.406)

In the indication, up to 99999.9 h (=11,4 years)
can be indicated.

Operating hours counter (Addr. 394)

The operating hours counter measures the time,
in which the UMG96S detects and indicates
measured data. The operating hours counter
cannot be reset.

Total running time comparators

The total running time of a comparator is the
sum of all time, in which the comparator result
violates its limit. The total running time of each
comparator can be reset individually.

L1

L2

L3

h

Working hours counter

Example:
Indication of operating hours
The UMG96S indicates the operating hours by
the number

140,8h

. This corresponds to 140

hours and 60 industrial minutes.
100 industrial minutes correspond to 60 min-
utes.
In this example, the 80 industrial minutes refer
to 48 minutes.

«
...
44
45
46
47
48
...
»

Содержание UMG 96S

































































































Отзывы:

Нет отзывов

Похожие инструкции для UMG 96S

Бренд: Farfisa Страницы: 14

Бренд: Valmet Страницы: 63

IEM-100 Beltpack

Бренд: DAPAudio Страницы: 19

Бренд: janitza Страницы: 6

Бренд: janitza Страницы: 36

Бренд: VeEX Страницы: 842

Бренд: P3 International Страницы: 2

Бренд: OBDPROG Страницы: 8

Бренд: Burkert Страницы: 192

Бренд: ACCRETECH Страницы: 104

PHYSICS line C.A 832

Бренд: Chauvin Arnoux Страницы: 43

Бренд: JBM Страницы: 4

Бренд: TE Connectivity Страницы: 3

Rangemaster CRF 1000

Бренд: Leica Страницы: 118

Бренд: SloanLED Страницы: 3

Бренд: Ecodhome Страницы: 12

HX3 Drawbar Expander Version 5

Бренд: KEYBOARDPARTNER Страницы: 11

Бренд: Tektronix Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды