Isel IMD20 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 135

background image

Positioning module IMD20, IMD40

ACSetup programme

The maximum speed is determined internally and then limited to 95 %, in order to dispose of a good
reserve for the regulation.

Important:

If a current short circuit fault (fault number 13) occurs during the automatic determination

Pos

of the maximal velocity the user must reduce step by step the current limitation (in the main iq_Limit)
until the fault 13 does not occur anymore.

ition Controller dialogue box

The position controller is a PD controller with velocity feed forward. This is superimposed on the
velocity controller, i.e. the velocity controller has to be set first. A feed forward always leads to better
dynamics, but also to an following. Normally, the default values for he feed forward should be
applied.

For the test of the settings, a test signal is again available consisting of three impulses with different
signs. The ramp slope can be chosen

en the (previously determined) maximum acceleration

nd a maximum ramp (jump).

In order to be able to assess the settings, the display options speed and following error (control

betwe

a

deviation) are available.

69

«
...
67
68
69
70
71
...
»

Содержание IMD20








































































































































Отзывы:

Нет отзывов

Похожие инструкции для IMD20

Бренд: Accel Страницы: 8

Бренд: Danfoss Страницы: 7

Бренд: Gardena Страницы: 18

VLT Micro Drive FC 51 Series

Бренд: Danfoss Страницы: 23

Бренд: jablotron Страницы: 22

Бренд: jablotron Страницы: 2

Бренд: Mackie Страницы: 4

Бренд: Taco Electronic Solutions Страницы: 28

Бренд: Linear Technology Страницы: 7

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 25

eTracer ET4415BND

Бренд: Epsolar Страницы: 44

Бренд: Graco Страницы: 166

Бренд: Penn Страницы: 10

Бренд: Beckhoff Страницы: 67

Бренд: ENTRYPASS Страницы: 27

Бренд: Omron Страницы: 12

Бренд: J+J Страницы: 91

Бренд: Danfoss Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды