Invacare Excelerator XLT Скачать руководство пользователя страница 74

Страница: 74 / 96

9 SERVICE PROCEDURES

Invacare® Top End® Recreation Handcycles

Part No 1171891

9.13 Removing/Installing the Front Wheel

XLT PRO

Removing

Open the quick-release lever securing the front wheel to the fork (Detail "A") and loosen the knob on the opposite side of the quick-release lever.

Remove the wheel from the fork.

Remove the chain from the front wheel.

Installing

Loop the chain over the front wheel sprocket.

Position the front wheel axle into the fork slots.

Tighten the knob on the opposite side of the quick-release lever and secure the wheel to the fork with the quick-release lever.



WARNING

After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or
damage may occur.



For ease of installation, secure the handcycle frame approximately 6 inches from the ground or seek assistance.

Chain

Sprocket

Front Wheel

Fork

DETAIL “A”

- FRONT WHEEL

QUICK-RELEASE LEVER

Quick-release Lever

Содержание Excelerator XLT

































































































Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды

Invacare Excelerator XLT, Руководство пользователя

Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды