Invacare Excelerator XLT Скачать руководство пользователя страница 30

Страница: 30 / 96

4 SAFETY INSPECTION/TROUBLESHOOTING

Invacare® Top End® Recreation Handcycles

Part No 1171891

Recommended tire pressure is listed on the side wall of the tire. If tire needs replaced, contact a local bike shop for replacement.

The wheels and tires should be checked periodically for cracks and wear, and should be replaced if damaged.

Check chain for slack and readjust if necessary. Installing/Adjusting Twenty-Seven Speed Cassette Chain on page 70.

Regularly check for loose spokes in the front and rear wheels. If loose, have them aligned at your local bike shop.

10. Check road crown compensator for proper operation. Refer to Installing/Removing/Adjusting the Road Crown Compensator on page 63.

11. Check upholstery for sagging, rips or tears. Refer to Replacing Seat Upholstery on page 81.

12. Check alignment of front wheel. If it wobbles or takes too much effort to turn by hand, have it aligned at your local bicycle shop.



CAUTION

As with any vehicle, the wheels and tires should be checked periodically for cracks and wear, and should be replaced.

Содержание Excelerator XLT

































































































Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды

Invacare Excelerator XLT, Руководство пользователя

Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды