Invacare Excelerator XLT Скачать руководство пользователя страница 6

Страница: 6 / 96

1 GENERAL

Invacare® Top End® Recreation Handcycles

Part No 1171891

1 General

1.1

Symbols

Warnings

Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage.

See the information below for definitions of the signal words.

1.2

Dealer/Technician Information

The term “qualified technician” in this manual refers to an Invacare qualified technician or a Shimano® certified bicycle repair technician.



DANGER

Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.



WARNING

Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.



CAUTION

Caution indicates a potentially hazardous situation which, if not avoided, may result in property damage or minor injury or
both.

IMPORTANT

Indicates a hazardous situation that could result in damage to property if it is not avoided.



Gives useful tips, recommendations and information for efficient, trouble-free use.

Содержание Excelerator XLT

































































































Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды

Invacare Excelerator XLT, Руководство пользователя

Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды