Invacare Excelerator XLT Скачать руководство пользователя страница 60

Страница: 60 / 96

9 SERVICE PROCEDURES

Invacare® Top End® Recreation Handcycles

Part No 1171891

Excelerator Series

Install washer and ball bearing housing onto fork assembly.

Slide fork assembly through the opening in the front frame (Goose

Neck).

Install ball bearings onto the fork assembly.

Place the locknut over the fork assembly and tighten.

Tighten the setscrews.

Tighten the eyebolts onto the fork assembly and front frame.

Using a medium flat screwdriver, hook the tension spring to the

fork assembly and front frame eye bolts.



The tension spring is NOT intended to keep the
handcycle straight when pedaling but to keep the
handcycle from leaning excessively to one side or
another.



Tension is applied by lossening or tightening the eye
bolts. This should be done before installation of the
tension spring.

Set Screws

Locknut

Ball Bearing

Gooseneck

Front Frame Opening

Ball Bearing Housing

Washer

Fork Assembly

Eyebolt

Tension Spring

Eyebolt

Front Frame

Adjustable

Chain Idler

Содержание Excelerator XLT

































































































Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды

Invacare Excelerator XLT, Руководство пользователя

Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды