Invacare Excelerator XLT Скачать руководство пользователя страница 75

Страница: 75 / 96

9 SERVICE PROCEDURES

Part No 1171891

Invacare® Top End® Recreation Handcycles

XLT, XLT jr., Excelerator and Li’l Excelerator

Removing

Remove the hex bolt and locknut that secure the brake arm to the brake arm clamp (Detail “A”).

Loosen, but do not remove the two cap nuts that secure the front wheel to the existing fork (Detail “B”).

Remove the front wheel from the existing fork.

Remove the chain (not shown) from the front wheel hub.

Installing

Loop the chain (not shown) over the front wheel hub (Detail “B”).

Position the front wheel axle into the fork slots.

Line up the projecting ends of the non-turn washer with the slot in the fork.

Torque the two cap nuts to 260-390 in-lbs (29.4 - 44.0 n-m).

Secure the brake arm to the brake arm clamp with the hex bolt and locknut (Detail “A”). Torque to 22-26 in-lbs.



Make sure the washer and non-turn washer are on the outside of the fork.

Detail “A”

Detail “B”

Brake

Arm

Clamp

Hex Bolt

Brake Arm

Locknut

Fork

Washer

Front

Wheel

Hub

Cap Nuts

Non-Turn Washer-MUST Be

Installed as Shown

Non-Turn Washer

Slot

Содержание Excelerator XLT

































































































Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды

Invacare Excelerator XLT, Руководство пользователя

Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды