Invacare Excelerator XLT Скачать руководство пользователя страница 28

Страница: 28 / 96

4 SAFETY INSPECTION/TROUBLESHOOTING

Invacare® Top End® Recreation Handcycles

Part No 1171891



Inspect upholstery for rips or sagging.



Clean upholstery with light detergent and water.



Check that all labels are present and legible. Replace if necessary.



Ensure that axles are free of debris.

Inspect/Adjust Periodically



Inspect upholstery for rips or sagging.



Clean upholstery with light detergent and water.



Inspect hand grips for looseness. If loose, replace.



Check that all labels are present and legible. Replace if necessary.

4.2

Troubleshooting

Veers

Right

Veers

Left

Sluggish Turn

or Performance

Wheel
Flutter

Squeaks

and Rattles

Looseness

in Handcycle

Solutions

Check road crown compensator and adjust to neutral

Check tires for correct and equal pressure

Check hardware and adjustment.

Check for loose axle nuts.

Check spokes and nipples.

Check chain for proper tension and adjustment.

Check that goose neck fittings are secure.

Содержание Excelerator XLT

































































































Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды

Invacare Excelerator XLT, Руководство пользователя

Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды