Invacare Excelerator XLT Скачать руководство пользователя страница 70

Страница: 70 / 96

9 SERVICE PROCEDURES

Invacare® Top End® Recreation Handcycles

Part No 1171891

9.10 Installing/Adjusting Twenty-Seven Speed Cassette Chain
XLT PRO
Installing Twenty-Seven Speed Cassette Chain

Spread the chain out flat and run it around the chain ring on the crank and the sprocket on the hub.

Ensure that crank assembly is loosened.

Lift up on the chain derailleur and thread the chain under the derailleur.

Thread the chain around the wheel sprocket.

Run the chain around the bottom of the wheel sprocket and back up towards the hand crank sprocket.

Attach the chain together using the master link (w/clip) provided.

To tension chain, Refer to Replacing Fork/Crank Assembly on page 56.



It may be necessary to turn the hand crank in a clockwise motion to position the chain on the small sprocket.

STEP 5

STEP 4

STEP 3

Hand Crank Sprocket Assembles

Chain Derailleur and Wheel Sprockets

Содержание Excelerator XLT

































































































Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды

Invacare Excelerator XLT, Руководство пользователя

Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды