Invacare Excelerator XLT Скачать руководство пользователя страница 76

Страница: 76 / 96

9 SERVICE PROCEDURES

Invacare® Top End® Recreation Handcycles

Part No 1171891

9.14 Replacing/Adjusting the Parking Brake

Adjusting

Cable

Loosen the hex nut and turn the adjuster barrel clockwise (tighten) or

counterclockwise (loosen) to adjust the cable. Retighten hex nut.

Brake Pads

Adjust the brake pad assembly so that when the parking brake is engaged

the brake pads rest solely on the rim of the wheel.

Replacing

Brake Pads

Remove the mounting nuts and brake pads.

Secure the replacement brake pads with hardware and adjust.



WARNING

After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or

damage may occur.

Replacement of the parking brake MUST be performed by a qualified technician.

Parking Brake

Содержание Excelerator XLT

































































































Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды

Invacare Excelerator XLT, Руководство пользователя

Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды