Invacare Excelerator XLT Скачать руководство пользователя страница 66

Страница: 66 / 96

9 SERVICE PROCEDURES

Invacare® Top End® Recreation Handcycles

Part No 1171891

9.7

Installing Seven Speed Shifter Cable

Excelerator and Lil’ Excelerator

Run the cable from the right-side of the fork assembly to mounting position on the left side just below the hand crank assembly.

Attach the seven speed shifter to the hand crank assembly extension.

Secure with hardware provided.

XLT and XLT Jr.

Run the cable from the right-side of the fork assembly to mounting position on the left side just below the left side of the seat.

Attach the seven speed shifter to the seat rail.

Secure with hardware provided.



The seven speed Shifter Cable runs from the right side of the front frame to its mounting position on the hand crank assembly.



The seven speed Shifter Cable runs from the right side of the front frame to its mounting position under the left side of the seat.

Hand Crank

Assembly

Extension

Shifter

Cable

Shifter

Excelerator and Lil’ Excelerator

XLT and XLT Jr.

Содержание Excelerator XLT

































































































Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды

Invacare Excelerator XLT, Руководство пользователя

Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды