Invacare Excelerator XLT Скачать руководство пользователя страница 82

Страница: 82 / 96

9 SERVICE PROCEDURES

Invacare® Top End® Recreation Handcycles

Part No 1171891

9.20 Replacing Back Upholstery
Wide Back Upholstery

Unlatch the two fastening flaps that secure the bottom of existing

back upholstery to the back canes.

Unlatch the top of the existing back upholstery.

Lift up on the existing back upholstery and remove from the

handcycle.

Install the new back upholstery onto the handcycle.

Securely latch the fastening flaps on the bottom of the new back

upholstery to the back canes.



WARNING

Upholstery MUST be inspected before each use.

Exposure to moisture (i.e. - wet weather or puddles)

will damage fastening straps/flaps/strips. DO NOT

operate handcycle if upholstery is wet or damaged,

otherwise severe injury may occur.

Fastening

Flap

Back

Upholstery

Fastening

Flap

Back Cane

Содержание Excelerator XLT

































































































Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды

Invacare Excelerator XLT, Руководство пользователя

Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды