Invacare Excelerator XLT Скачать руководство пользователя страница 67

Страница: 67 / 96

9 SERVICE PROCEDURES

Part No 1171891

Invacare® Top End® Recreation Handcycles

9.8

Adjusting/Replacing Seven Speed Shifter

It is recommended that you take your handcycle to a qualified technician for any shifter adjustment.
Handcycles with seven speed shifters are equipped with SHIMANO hubs. If equipped with a SHIMANO hub, it MUST be serviced and adjusted by a

qualified technician.

9.9

Installing/Adjusting Seven Speed Hub Chain

Installing

Spread the chain out flat and run it over the bottom chain tensioner upwards to the hand crank sprocket assembly.

Position chain over the hand crank sprocket assembly.

Run the chain over the top chain tensioner.

Position the chain around the wheel sprocket and back up towards the bottom chain tensioner.

Place chain over the top of the bottom chain tensioner.

Attach the chain together using the master link (with clip) provided.



QUALIFIED TECHNICIAN ONLY - Contact Invacare for complete Shimano hub instructions.



WARNING

Idler MUST be adjusted to ensure proper chain tension. If proper tension is not present, chain may disengage from the chainring. If the

chain is noisy when at proper tension, loosen slightly. After the chain is assembled, start in first gear and on straghtaway.



It may be necessary to turn the hand crank in a clockwise motion to position the chain on the sprocket.

Содержание Excelerator XLT

































































































Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды

Invacare Excelerator XLT, Руководство пользователя

Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды