Invacare Excelerator XLT Скачать руководство пользователя страница 41

Страница: 41 / 96

6 OPERATION

Part No 1171891

Invacare® Top End® Recreation Handcycles

Lower Derailleur (Right Side Shifter on Hand Pedal)

• Shifting from Harder Gears to Easier Gears (Downshift) -

Rapid Fire Shifter -

Push shift lever closest to center with thumb and release. Repeat until the desired gear is achieved.

• Shifting from Easier Gears to Harder Gears (Upshift) -

Rapid Fire Shifter -

Pull shift lever located towards the outside using thumb or index finger and release. Repeat until the desired gear is achieved.

Upper Derailleur (Manual Shifter on Crank Set)

• Shifting from Easier or Smaller Chainring to Harder or Larger Chainring (Upshift) -

Manual Shifter -

Move shifter lever up.
• Shifting from Harder or Larger Chainring to Easier or Smaller Chainring (Downshift) -

Manual Shifter -

Move shifter lever down.

Содержание Excelerator XLT

































































































Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды

Invacare Excelerator XLT, Руководство пользователя

Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды