Invacare Excelerator XLT Скачать руководство пользователя страница 69

Страница: 69 / 96

9 SERVICE PROCEDURES

Part No 1171891

Invacare® Top End® Recreation Handcycles

Adjusting the Chain Tensioner

Ensure the hand crank is adjusted to the proper height. .

Loosen the hex screw securing the adjustable chain idler.

Adjust the tautness of the chain by moving the adjustable chain tensioner in or out as shown in .

Tighten the hex screw to secure the adjustable chain tensioner in place.



WARNING

Idler MUST be adjusted to ensure proper chain tension. If proper tension is not present, chain may disengage from the chainring. If the

chain is noisy when at proper tension, loosen slightly. After the chain is assembled, start in first gear and on straghtaway.

Make sure the tensioner is aligned properly, otherwise the chain will fall off.



Repositioning the hand crank assembly loosens or tightens the chain in an up/down position.

Adjustable

Chain Idler

Hex Screw

Содержание Excelerator XLT

































































































Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды

Invacare Excelerator XLT, Руководство пользователя

Результаты поиска

Содержание Excelerator XLT

Отзывы:

Похожие инструкции для Excelerator XLT

Бренды по названию

Популярные бренды