Inner Range IQ plus Скачать руководство пользователя

Страница: 22 / 98

p22

Ver. 3.604 (31/03/05)

INNER RANGE IQ. PLUS Programmer’s Manual.

SELECT THE END-OF-LINE RESISTOR TYPE.

NEXT 600

DEFAULT: Option 3 - 3k3 Single End-of-Line.

END-OF-LINE RESISTOR TYPES:
Single EOL:

-1k

-1k5

-2k2

-3k3

-3k9

-4k7

-5k6

-6k8

-10k

-12k

-22k

Dual EOL:

-2k2, 2k2

-2k2, 6k8

-3k3, 6k8

-10k, 10k (Provides Tamper state. 1st Value is Series Resistor, 2nd Value is Resistor across contacts)

Zone Doubed:

-1k, 3k3, 6k8 Zone doubled

-1k, 3k3, 6k8 Zone doubled (no seperate tamper state)

See installation manual for details.

DEFAULT THE SYSTEM.

Logon to the Terminal using the Installer PIN code and select DEFAULTING THE CONTROL MODULE.

NEXT 098

-Enter PIN, <NEXT>, 0, 9, 8.

Select the Default Option.

! CAUTION: This option completely erases all current programming.

- n, <ENTER>.

Completely resets the database to Factory Default settings, including the Installer Code and Master Code.

Where “n” is the Default option.

1, 2 or 3:

Completely resets the database to one of the Installer Presets, including the Installer Code and Master Code.

See page 16 “Defaulting the system” and the “Factory Defaults” Table on page 85 for details.

Reset the Control Module.

Disconnect the AC Supply input and the Battery from the Control Module. Wait 5 seconds, then Re-connect power.

PROGRAM THE ZONE TYPE/S.

NEXT 601 to 616

DEFAULT: Zone 1; Type 1-Delayed.

Zone 2; Type 2-Handover

Zones 3 to 16; Type 0-Instant.

Program the new Zone Type for Zones that are not “Instant” Zones.

Zone Types:

Instant

Delayed

Handover

Away Instant / Home Isolate

Away Instant / HomeDelay

Away Delay / Home Isolate

Away Delay / Home Delay

Away Delay / Home Instant

Away Handover / Home Isolate

Away Handover / Home Delay

24 Hour Burglary

24 Hour Fire

24 Hour Panic

24 Hour duress

KeySwitch Arm

KeySwitch Home

Delay / Force Arm

Handover / Force Arm

Zone

Address

601

602

603

604

605

606

607

608

609

610

611

612

613

614

615

616

Содержание IQ plus



































































































Результаты поиска

Содержание IQ plus

Отзывы:

Похожие инструкции для IQ plus

Бренды по названию

Популярные бренды

Inner Range IQ plus, Руководство программиста

Результаты поиска

Содержание IQ plus

Отзывы:

Похожие инструкции для IQ plus

Бренды по названию

Популярные бренды