iColor I Candy 200 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 72

background image

|

14

User Manual – February 2020 Edition

0.5

1.0

1.5

0.5

12.7

25.4

38.1

12.7

mm

in.

2.0

1.5

1.0

0.5

12.7

25.4

38.1

50.8

mm

in.

LABEL STOCK SENSOR SLIDE

C. Adjusting the gap sensor

If you are using label stock other than standard square / rectangular die-cut labels such as circular die-cut labels or
through-hole stock use the instructions below to adjust the position of the label stock gap sensor. The sensor can
be adjusted using the slide bar on the inside of the printer. Below the slide bar is a measurement which represents
the distance between the edge of the label stock and the sensor. Measure the distance from the edge of the label
stock to the correct position on the stock. Set the sensor so the side of the slide bar lines up to this measurement.
See dashed line in the illustration below.

Important Note!

You must adjust the stock sensor before loading nonstandard label stock.

Circular Labels

If you are using Circular Labels you must adjust the stock sensor to correspond with the very top of the label where
the circles are closest together. If the sensor is too far to the right or the left the printer will still sense the label but
the image may be offset downward because the printer will start printing at the wrong position. If you are using stock
that has multiple labels across make sure the sensor corresponds to a place on the stock that has a label and not a
vertical gap.

The sensor can only be moved a maximum of 2 inches from the left side of the printable area. This means that the
maximum diameter circular label that can be printed is 4 inches. For circular labels larger than 4 inches in diameter,
you must have a black mark printed on the back of the label stock. This means that you must change the Stock
Sensor Mode to Reflective. The printer will now look for the black mark representing the beginning of the next label
instead of the die-cut. For more information on changing the Stock Sensor Mode see Section 2D.

«
...
13
14
15
16
17
...
»

Содержание I Candy 200









































































Отзывы:

Нет отзывов

Похожие инструкции для I Candy 200

Бренд: MAGIMIX Страницы: 46

Бренд: ZAGGIA Страницы: 18

Intelia Deluxe HD8902

Бренд: Saeco Страницы: 56

Бренд: Farberware Страницы: 27

Бренд: Saeco Страницы: 96

Бренд: Unimark Страницы: 43

VELASCA PRESTIGE

Бренд: Gaggia Страницы: 56

Бренд: Xiamen Hanin Electronic Страницы: 21

Бренд: DeLonghi Страницы: 10

Бренд: Hamilton Beach Страницы: 36

TWIN-MATRIX-6-R/L

Бренд: Labelmate Страницы: 6

Бренд: Dash Страницы: 32

Бренд: Jura Capresso Страницы: 36

IMPRESSA X9 Win

Бренд: Jura Страницы: 52

Horizon Elite HCD1010NJS

Бренд: Follett Страницы: 16

Бренд: Hamilton Beach Страницы: 19

Silhouette Select DIM3225BLSST

Бренд: Danby Страницы: 42

Designer Ice'n Easy DIM1524W

Бренд: Danby Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды