iColor I Candy 200 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 72

background image

|

22

User Manual – February 2020 Edition

To see a printable/saveable report click on the document icon next to the job you want to see. A report will display
the information. You can print or save the report from this screen. You can also change the currency using the drop
down, change the job name or adjust the cost from this screen.

Important Note!

The cost per label represents the average cost per label over an entire run of labels. This means that the per label cost
will decrease and become more accurate as the number of labels printed increases. This is because the ink that is used
for periodic cartridge maintenance is divided into a larger number of labels. Uninet recommends printing at least 5 labels
for an accurate per label cost.

«
...
21
22
23
24
25
...
»

Содержание I Candy 200









































































Отзывы:

Нет отзывов

Похожие инструкции для I Candy 200

Бренд: Brew Express Страницы: 20

Бренд: Mixpresso Страницы: 16

Glacons Express

Бренд: Lagrange Страницы: 48

Бренд: Farberware Страницы: 15

Бренд: Saeco Страницы: 48

Бренд: Prowill Страницы: 4

Accents 162005EE

Бренд: Morphy Richards Страницы: 40

Бренд: Daewoo Страницы: 29

Бренд: Aurora Страницы: 12

Бренд: SATO Страницы: 2

Бренд: Omcan Страницы: 16

Clatronic TKS 3504

Бренд: CTC Union Страницы: 60

Бренд: Omcan Страницы: 24

Бренд: KitchenAid Страницы: 1

Бренд: Stalgast Страницы: 10

Бренд: Philips Страницы: 5

Бренд: Philips Страницы: 4

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды