iColor I Candy 200 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 72

background image

|

60

User Manual – February 2020 Edition

B. Solving print quality problems

Many factors can affect the quality of the print.

The following are listed in order from most likely to least likely:

1.

Quality Setting
Change your quality setting. The lowest (and fastest printing) quality may not be sufficient for many
photos or graphics. The highest quality setting may cause ink to bleed on certain graphics in combination
with certain label stock. Increasing the quality increases print time because the printer makes more
horizontal movements across the label.

2.

Clean the Cartridge
Run an automatic cleaning print or manually clean the cartridge as described in Section 6D.

3.

Change the Cartridge
Try a new cartridge. Make sure that the ink cartridge has ink remaining. Check the ink levels via the
IColor 200 PrintHub or Printer Utility (Mac).

4.

Align Print Head
Normally, print head alignment is only necessary after changing a print head. However, in certain cases,
running the alignment again can improve print quality. Align the print head by opening the IColor 200
PrintHub or Printer Utility (Mac). Click on the Align Print Head button on the Cartridge Utilities Tab
(second tab). Follow the onscreen prompts to load your paper for alignment.

5.

Clean the Maintenance Station
Power off the printer! Gently move the cartridge to the left to access the maintenance station. Clean the
maintenance station located on the right side of the print area. This includes the rubber cartridge nozzle
cap and the plastic roller. Under normal use this can become dirty with ink. Clean with rubbing alcohol
and a paper towel.

6.

Color Matching.
Change your Color Matching setting to Graphics or Photos via the printer driver preferences.
See Section 4G or 5H.

Maintenance station

«
...
59
60
61
62
63
...
»

Содержание I Candy 200









































































Отзывы:

Нет отзывов

Похожие инструкции для I Candy 200

Бренд: Unic Страницы: 2

Бренд: La Spaziale Страницы: 11

Бренд: La Spaziale Страницы: 16

Бренд: GGMgastro Страницы: 257

Бренд: Hoshizaki Страницы: 43

Бренд: Proline Страницы: 40

Бренд: Hoshizaki Страницы: 30

Бренд: Beem Страницы: 72

Бренд: Saeco Страницы: 37

Бренд: JDE Страницы: 18

Бренд: Ice-O-Matic Страницы: 32

Black&White 3 CBT

Бренд: Thermoplan Страницы: 1

Бренд: HAEGER Страницы: 44

Бренд: tomado Страницы: 76

Бренд: Kalorik Страницы: 24

Бренд: Carnival King Страницы: 3

Бренд: Hoshizaki Страницы: 34

Бренд: Cremesso Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды