iColor I Candy 200 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 72

background image

|

65

User Manual – February 2020 Edition

7. Wipe nozzles.

A.

Place second paper towel on flat/hard
surface.

B.

Press the nozzles into the paper towel.

C.

Firmly tap the top of the cartridge three
times to force the ink out

D.

Wipe/drag the cartridge in the direction
indicated.

E.

Repeat until all colors are seen on the
paper towel.

After wiping the nozzles, the paper towel
should show all three colors.

If all three colors are present, proceed to
Step 8.

If the paper towel doesn’t show all three
colors, then repeat Step 7.

If paper towel still doesn’t show all three
colors repeat Step 7, then replace the
cartridge.

«
...
64
65
66
67
68
...
»

Содержание I Candy 200









































































Отзывы:

Нет отзывов

Похожие инструкции для I Candy 200

Бренд: Magic Chef Страницы: 3

Бренд: Vitrifrigo Страницы: 30

PrimaDonna Exclusive

Бренд: DèLonghi Страницы: 11

Balanced Living YG2328US

Бренд: T-Fal Страницы: 24

Бренд: san ignacio Страницы: 28

Бренд: Buffalo Страницы: 36

EP 4100 BIANCHI M

Бренд: BIANCHI VENDING Страницы: 48

Бренд: Farberware Страницы: 12

Бренд: Axis Страницы: 16

Бренд: Sangkee Страницы: 24

Бренд: Jenn-Air Страницы: 42

Бренд: Russell Hobbs Страницы: 45

Бренд: QuickLabel Systems Страницы: 485

Cafe Roma Deluxe 1329

Бренд: Espressione Страницы: 1

Бренд: MAKINA Страницы: 20

Бренд: Concordia Страницы: 46

Бренд: Korona Страницы: 24

Бренд: Miele Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды