iColor I Candy 200 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 72

background image

|

18

User Manual – February 2020 Edition

Present Options

Do Not Present

In this mode the label stock does not move after the last label is printed. This means that part of the last label
printed is still in the printer. This should be used only if you have a label rewinder attached.

Present After No Activity

This setting will present (feed all printed labels past the tear off point) at the end of a print job if the printer does
not receive another print job within one second of the last print job in the queue. You can use this feature to
present at the end of a multi-copy job, a multi-page job or multiple individual jobs in the queue.

«
...
17
18
19
20
21
...
»

Содержание I Candy 200









































































Отзывы:

Нет отзывов

Похожие инструкции для I Candy 200

Бренд: Saeco Страницы: 66

Xsmall Steam Xsmall Plus

Бренд: Saeco Страницы: 19

Бренд: Pacific Страницы: 13

Бренд: Krups Страницы: 16

Бренд: emerio Страницы: 60

Бренд: ACA Страницы: 23

Бренд: Malongo Страницы: 84

ESPRESSO COFFEE MACHINE

Бренд: ZAGATO Страницы: 16

Бренд: Klarstein Страницы: 64

Бренд: Fackelmann Страницы: 60

Бренд: WHITE BROWN Страницы: 16

Бренд: Champion Страницы: 12

Бренд: Gaggia Milano Страницы: 88

Бренд: Whirlpool Страницы: 9

Tassimo my way 2

Бренд: Bosch Страницы: 2

Бренд: STAKOL Страницы: 11

Бренд: LAVAZZA Страницы: 172

EQUINOX OP522D10

Бренд: OBH Nordica Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды