IBM SAN768B, Инструкция по установке, обслуживанию и эксплуатации, Страница: 58 / 208

v FC8-48 port blade - Ports are numbered from 0 through 23 from bottom to top
on the left set of ports and 24 through 47 from bottom to top on the right set of
ports.
v
FC8-64 port blade - Ports are numbered from 0 through 31 from bottom to top
on the left set of ports and 32 through 63 from bottom to top on the right set of
ports. See Figure 56 on page 157 for more information. Trunking groups are
permitted with up to eight ports per group. trunking groups are as follows: 0-7,
8-15, 16-23, 24-31, 32-39, 40-47, 48-55, and 56-63.
v FC10-6 port blade - Ports are numbered from 0 through 5 from bottom to top.
v
FR4-18i router blade - The 16 physical Fibre Channel ports are numbered from 0
through 15 from bottom to top. The two GbE ports, numbered GE0 and GE1, are
located below the Fibre Channel ports. These ports, when fully configured,
enable 16 VE_ports or VEX_ports and appear in the
switchShow command as
ports 16 through 31.
v
FS8-18 blade — The 16 physical Fibre Channel ports on this blade are numbered
0 through 15 from bottom to top. The two 10/100/1000 BaseT ports are
numbered from the bottom as GE0 and GE1.
v FX8-24 FCIP extension blade - The port numbering scheme is fairly complex for
this blade, but is displayed for reference on the blade itself in a diagram towards
the lower end of the blade. (See Figure 60 on page 161 for a description and
illustration of the port layout.) There are twenty-four physical ports. Twelve FC
ports are located towards the lower end of the blade, with ports 0 through 5 on
the left side, and ports 6 through 11 on the right side. Two 10 Gigabit Ethernet
(10GbE or XGE) ports are located in the middle of the blade on the left side, and
are numbered 0 and 1, from bottom to top. Ten GbE ports are located towards
the top of the blade, with eight clustered at the top, and the remaining two
located to the right of the two 10GbE ports. The GbE ports 0 through 3,
numbered from bottom to top are located on the left side at the top of the blade.
Ports 4 and 5 are located above the two 10GbE ports, and ports 6 through 9
(numbered bottom to top) are at the top on the right side, to the right of ports 0
through 3. Up to three FC trunking groups. The three groups are defined as:
– Trunk group 0: FC ports 0, 1
– Trunk group 1: FC ports 6, 7
– Trunk group 2: FC ports 2, 3, 4, 5, 8, 9, 10, 11
v FCoE10-24 FC over Ethernet blade - The 24 physical ports are numbered 0
through 11 from bottom to top on the right side, and 12 through 23 from bottom
to top on the left side (see Figure 61 on page 162).
Chassis slots
Slots are numbered 1 through 12, from left to right when facing the port side of the
SAN768B. Control processor blades (CP8) can be installed only in slots 6 and 7.
Core switch blades (CR8) can be installed only in slots 5 and 8. Port, application,
or encryption blades can be installed in slots 1–4 and 9–12. Unused slots must be
filled with blade filler panels to maintain adequate cooling.
See Appendix D, “Blade port numbering,” on page 153 for port numbering details
of the SAN768B port blades. Also refer to the IBM Redbook,
Implementing an
IBM/Brocade SAN with 8 Gbps Directors and Switches , SG24-6116, for more
comprehensive information on port numbering and area port numbering, and
other technical information. This publication is available through
www.redbooks.ibm.com/. Search by title or publication number.
26
SAN768B Installation, Service, and User Guide
|
|
|
|
|