IAI X-SEL PX Скачать руководство пользователя страница 426

Страница: 426 / 560

399

Appendix

16. Aborting of Operation 1 (CANC)

Description

Use a declarative command CANC to cause the moving axis to decelerate a stop and cancel the

remaining operation of the axis.

How to Use

While CANC is input, all movement commands issued in the same program are paused are aborted.

CANC command

CANC

Abort the movement command in the middle when input port 20 turns ON.

(Declaration)

MOVP 1

MOVP 2

WTON 21

* Declare this command in a step before a movement command.

* While CANC is input, all operation commands are cancelled one by one, but non-operation commands

(such as I/O processes and calculation processes) are performed according to the specified sequence.

Caution

Since which program step is currently executed becomes indeterminable, it is recommended that a WTON

command be used to create a step to wait for input.

Application

With a CANC command, you can select a desired pattern of input signal by using operand 2.

0 = Contact a (Deceleration to a stop)



Same as when operand 2 is not specified

1 = Contact b (Deceleration to a stop)

Input port 20 ON

Remaining

operation

Time



Speed



This operation is cancelled.

Cancellation input: 20 = Contact b

400

Appendix

17. Aborting of Operation 2 (STOP)

Description

Cause the moving axis to decelerate a stop and cancel the remaining operation of the axis. (STOP)

How to Use

Implement an abort using a STOP command issued from other program. (Multi-tasking mode)

Use an axis pattern to specify the axis you want to abort.

Example of Use 1

STOP command

Main program

Aborting control program

If “STOP 11” is executed while “MOVL 1” is still being executed, “MOVL 1” will be cancelled and

operation will continue from “MOVL 2.”

Example of Use 2

Main program

Aborting control program

If “STOP 10” is executed while “MOVP 1” is still being executed, only axis 2 corresponding to “MOVP

1” will be cancelled. Both axes 1 and 2 will operate from “MOVP 2.”

Caution

In the operation being performed is a CP operation (interpolation operation) started by MOVL, etc., the

operation of all axes will be cancelled regardless of the axis pattern specified by the STOP command.

Time



Input port 20 ON

Remaining

operation

Speed



This operation is cancelled.

Start an aborting program.

Wait for an abort input.
Abort axes 1 and 2.

Wait for an abort input.
Abort axis 2.

402

Содержание X-SEL PX

















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X-SEL PX

Отзывы:

IAI X-SEL PX, Руководство по эксплуатации, Страница: 426 / 560

Результаты поиска

Содержание X-SEL PX

Отзывы: