IAI X-SEL PX Скачать руководство пользователя страница 284

Страница: 284 / 560

257

Part 4 Commands



TMLI (Dedicated SCARA command: Move relatively between positions on tool coordinate system via

interpolation in CP operation)

Command, declaration

Extension condition

(LD, A, O, AB, OB)

Input condition

(I/O, flag)

Command,

declaration

Operand 1

Operand 2

Output

(Output, flag)

Optional Optional TMLI Position

number

Prohibited PE

[Function] Each axis will move relatively on the tool coordinate system with interpolation (= CP

operation) based on the position data specified in operand 1 setting the travel amount from

the current position.

(Note 1)

This command is used exclusively for SCARA axes. If it is specified for a linear movement

axis, an “Error No. B80, Specification-prohibited axis error” or “Error No. 421, SCARA/linear

movement axis simultaneous specification error” will generate.

(Note 2)

Repeated use of incremental (relative) movement commands will accumulate coordinate-

conversion rounding errors.

[Example]

TMLI 120

Position data

Tool coordinate home

after movement

Tool coordinate home

before movement

Yt1

-Yt1

-30



Xt1

258

Part 4 Commands



PTRQ (Change push torque limit parameter)

Command, declaration

Extension condition

(LD, A, O, AB, OB)

Input condition

(I/O, flag)

Command,

declaration

Operand 1

Operand 2

Output

(Output, flag)

Optional Optional PTRQ Axis

pattern

Ratio CC

[Function] Change the push torque limit parameter for the axis pattern specified in operand 1 (among

SCARA axes, this command can be specified only for the Z-axis) to the value specified in

operand 2. The ratio in operand 2 is set as an integer (unit: %).

"Driver-card parameter No. 38: Push torque limit at positioning" can be rewritten temporarily

using a PTRQ command.

(Note 1)

If push torque limit is not set with a PTRQ command, the value set in "Driver-card

parameter No. 38: Push torque limit at positioning" will be used.

(Note 2)

If the push torque limit is changed, the new setting will remain valid even after the program

ends. Therefore, to build a system using PTRQ commands, a push torque limit must be

expressly specified with a PTRQ command before operation of each program. An

assumption that the push torque limit will be reset to the original value when the operation

ends in other program may lead to an unexpected problem, because the push torque limit

will become different from what is anticipated in case the applicable program is aborted due

to error, etc.

(Note 3)

The new value set with a PTRQ command will become invalid after a power-ON reset or

software reset.

(Note 4)

The value set in "Driver-card parameter No. 38: Push torque limit at positioning" (in the

main CPU flash memory (nonvolatile memory)) will not be written by a PTRQ command.

[Example]

PTRQ

100

Change the push torque limit parameter for the Z-axis to

50%.

PAPR

Set the push-motion approach distance to 50 mm and

push-motion approach speed to 20 mm/sec.

MOVP 10

Move to position No. 10.

PUSH 11

Move from position No. 10 to position No. 11 via push-

motion operation.

260

Содержание X-SEL PX

















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X-SEL PX

Отзывы:

IAI X-SEL PX, Руководство по эксплуатации, Страница: 284 / 560

Результаты поиска

Содержание X-SEL PX

Отзывы: