IAI acon Скачать руководство пользователя страница 99

Страница: 99 / 216

3. SCON-CA

PLC

output

SCON-CA input side (* “n” indicates the byte address of each axis.)

DO on the SCON-CA side and output data register

Position/Simplified

direct value mode 2

Half direct value

mode 2

Remote I/O mode 3

Half direct value

mode 3

PLC input

area

(bytes)

Number of occupied

bytes: 8

Number of occupied

bytes: 16

Number of occupied

bytes: 12

Number of occupied

bytes: 16

n+0, n+1

Port No.0 to 15

n+2, n+3

Target position

Target position Target

position

n+4, n+5

Specified position

number

n+6, n+7

Control signal

Positioning band

n+8, n+9

Speed

n+10, n+11

Acceleration/

Deceleration

Occupied area

Acceleration/

Deceleration

n+12, n+13

Pressing

current-limiting

value

Pressing

current-limiting

value

n+14, n+15

Control signal

n+16, n+17

n+18, n+19

n+20, n+21

n+22, n+23

n+24, n+25

n+26, n+27

n+28, n+29

n+30, n+31

(Note) The Occupied area shows the domain to be occupied with the operation mode setting.

Therefore, this domain cannot be used for any other purpose. Also, exercise caution to avoid node
address duplication.

Содержание acon

























































































































































































































Результаты поиска

Содержание acon

Отзывы:

IAI acon, Руководство по эксплуатации, Страница: 99 / 216

Результаты поиска

Содержание acon

Отзывы: