manualshive.com logo in svg

IAI acon, Руководство по эксплуатации, Страница: 43 / 216

Поделиться
Скачать
IAI acon Скачать руководство пользователя страница 43

2. ACON, 

PCON

37

(* “ON” in the table shows the corresponding bit of “1” and “OFF” shows “0”.) 

Signal type 

Bit 

Symbol 

Contents 

Details 

Current 

position 

32-bit

data

-

32-bit signed integer indicating the current position 
The setting unit is 0.01mm. 
(Example) Reading:  000003FF

H

=1023 (decimal) 

=10.23mm

*  When the value is read in hexadecimal notation, the negative 

figure is expressed as

 a complement of 2. 

2.8 (2) 

Command 

current 

32-bit

data

-

32-bit integer 
The electrical current presently specified by a command is indicated.
The setting unit is mA.   
(Example) Reading:  000003FF

H

=1023 (decimal) 

=1023mA

2.8 (2) 

Current 

speed 

32-bit

data

-

32-bit signed integer indicating the current position 
The current speed is indicated. 
Positive value: The actuator is moving in the direction opposite 
home.
Negative value: The actuator is moving in the direction of home. 
The setting unit is 0.01mm/sec.   
(Example) Reading:  000003FF

H

=1023 (decimal) 

=10.23mm/sec 

*  When the value is read in hexadecimal notation, the negative 

figure is expressed as a complement of 2. 

2.8 (2) 

Alarm code 

16-bit

data

-

16-bit integer 
When an alarm is issued, the alarm code is output. 
When any alarm is not issued, it is “0

H

”.

Refer to the operation manual for the controller main body for the 
details of the alarms. 

2.8 (2) 

b15 EMGS 

Emergency stop: An emergency stop is actuated when this signal 
turns ON. 

2.6.7 (2)

b14 PWR 

Controller ready: This signal turns ON when the controller becomes 
ready.

2.6.7 (1)

b13 ZONE2 

Zone 2: “ON” for the current position within the zone set range 

2.6.7 (12)

b12 ZONE1 

Zone 1: “ON” for the current position within the zone set range 

2.6.7 (12)

b11

b10

b9

-

Unavailable - 

b8 RMDS 

Operation mode status: 
This signal is OFF when the current mode is AUTO, or ON when the 
current mode is MANU. 

2.6.7 (19)

b7

b6

-

Unavailable - 

b5 PSEL 

Pressing and a Miss: This signal turns ON when the actuator 
missed the work part in pressing operation. 

2.6.7 (23)

b4 SV 

Operation preparation end: This signal turns ON when the servo 
turns ON. 

2.6.7 (5)

b3 ALM 

Alarm: This signal turns ON when an alarm occurs. 

2.6.7 (3)

b2 MOVE 

Moving signal: This signal remains ON while the actuator is moving.

2.6.7 (9)

b1 HEND 

Home return completion: This signal turns ON when home return is 
completed.

2.6.7 (6)

PLC input 

Status

signal 

b0 PEND 

Positioning completion signal: This signal turns ON when 
positioning is completed. 

2.6.7 (10)

Содержание acon

























































































































































































































Отзывы:

Нет отзывов