IAI acon Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 216

IAI acon Скачать руководство пользователя страница 11

5

No.

Operation

Description

Description

8 Maintenance

and Inspection

When the work is carried out with 2 or more persons, make it clear who is to be

the leader and who to be the follower(s) and communicate well with each other to
ensure the safety of the workers.

Perform the work out of the safety protection fence, if possible. In the case that the

operation is to be performed unavoidably inside the safety protection fence,
prepare the “Stipulations for the Operation” and make sure that all the workers
acknowledge and understand them well.

When the work is to be performed inside the safety protection fence, basically turn

OFF the power switch.

When the operation is to be performed inside the safety protection fence, the

worker should have an emergency stop switch at hand with him so that the unit
can be stopped any time in an emergency.

When the operation is to be performed inside the safety protection fence, in

addition to the workers, arrange a watchman so that the machine can be stopped
any time in an emergency. Also, keep watch on the operation so that any third
person can not operate the switches carelessly.

Place a sign “Under Operation” at the position easy to see.
For the grease for the guide or ball screw, use appropriate grease according to the

Operation Manual for each model.

Do not perform the dielectric strength test. Failure to do so may result in a damage

to the product.

When releasing the brake on a vertically oriented actuator, exercise precaution not

to pinch your hand or damage the work parts with the actuator dropped by gravity.

* Safety protection Fence : In the case that there is no safety protection fence, the

movable range should be indicated.

9 Modification

and

Dismantle

Do not modify, disassemble, assemble or use of maintenance parts not specified

based at your own discretion.

10

Disposal

When the product becomes no longer usable or necessary, dispose of it properly

as an industrial waste.

Do not put the product in a fire when disposing of it.

The product may burst or generate toxic gases.

«
...
9
10
11
12
13
...
»

Содержание acon

























































































































































































































Отзывы:

Нет отзывов