IAI acon Скачать руководство пользователя страница 27

Страница: 27 / 216

2. ACON,

PCON

(1) PLC address configuration (* “n” indicates the first address of each axis.)

Parameter

No.84

ACON/PCON

DI (Port No.)

PLC output

address (bytes)

ACON/PCON

DO (Port No.)

PLC input address

(bytes)

0 to 15

n+0, n+1

0 to 15

n+0, n+1

(Note) Be careful of using duplicated node addresses.

(2) I/O signal allocation for each axis

The I/O signals of each axis consist of one input word (1 word = 2 bytes) and one output word in the I/O
areas.

This is controlled by ON/OFF bit signals from the PLC.

PCL output
Address (* “n” indicates the first output address of each axis.)

PCL input
Address (* “n” indicates the first input address of each axis.)

Controller

input port

number

1 word = 2 bytes =16 bit

n+0

n+1

Controller

output port

number

1 word = 2 bytes =16 bit

n+0

n+1

Содержание acon

























































































































































































































Результаты поиска

Содержание acon

Отзывы:

IAI acon, Руководство по эксплуатации, Страница: 27 / 216

Результаты поиска

Содержание acon

Отзывы: