manualshive.com logo in svg

IAI acon, Руководство по эксплуатации, Страница: 155 / 216

Поделиться
Скачать
IAI acon Скачать руководство пользователя страница 155

3. SCON-CA

149

(* “ON” in the table shows the corresponding bit of “1” and “OFF” shows “0”.) 

Signal type 

Bit 

Symbol 

Description 

Details 

Pressing

current-limiting 

value

16-bit data 

- 

16-bit integer. 
Specify the current-limiting value during pressing operation. 
The specified range is 0 (0%) to 255 (100%). 
The actual specifiable range varies with each actuator. (Refer to 
the catalog or operation manual for each actuator.) 
If a move command is issued by specifying a value exceeding the 
maximum pressing current value, an alarm will occur. 

3.8 (2) 

b15 BKRL 

Forced brake release: The brake is released when the signal 
turns ON. 

3.6.11 (18)

b14 RMOD 

Operation mode: AUTO mode when the signal is OFF, or MANU 
mode when the signal is ON.   

3.6.11 (19)

b13 DIR 

Pressing direction specification: 
When the signal is OFF, the direction of the position obtained by 
subtracting the positioning band from the target position is used. 
When the signal is ON, the direction of the position obtained by 
adding the positioning band to the target position is used. 

3.6.11 (22)

b12 PUSH 

Pressing specification: Positioning operation when the signal is 
OFF, or pressing operation when the signal is ON. 

3.6.11 (21)

b11 GSL1 

Servo gain 
parameter set 
selection 1 

b10 GSL0 

Servo gain 
parameter set 
selection 0 

Select the servo gain parameter set to be 
used.

GSL1

GSL0 Function 

OFF 

OFF 

Select parameter set 0.

OFF 

ON 

Select parameter set 1.

ON 

OFF 

Select parameter set 2.

ON 

ON 

Select parameter set 3.

3.6.11 (33)

b9 NTC1 

Vibration 
damping control 
mode selection 1

b8 NTC0 

Vibration 
damping control 
mode selection 0

Select the vibration damping control 
parameter set to be used. 

NTC1

NTC0 Function 

OFF 

OFF 

Do not use vibration 
damping control.   

OFF 

ON 

Select parameter set 1.

ON 

OFF 

Select parameter set 2.

ON 

ON 

Select parameter set 3.

3.6.11 (29)

b7 MOD1 

b6 MOD0 

Acceleration / deceleration mode: 
When both MOD1 and MOD0 are OFF, the trapezoid pattern 
mode is selected. 
When MOD1 is OFF and MOD0 is ON, the S-motion mode is 
selected.
When MOD1 is ON and MOD0 is OFF, the primary delay filter 
mode is selected. 

3.6.11 (30)

b5 

- 

Cannot be used. 

- 

b4 

SON 

Servo ON command: The servo is ON when the signal is ON. 

3.6.11 (5)

b3 

RES 

Reset: A reset is performed when the signal turns ON. 

3.6.11 (4)

b2 

STP 

Pause: A pause command is issued when the signal turns ON. 

3.6.11 (11)

b1 HOME 

Home return: A home return command is issued when the signal 
turns ON. 

3.6.11 (6)

PLC output 

Control signal 

b0 DSTR 

Positioning start command: A move command is issued when the 
signal turns ON. 

3.6.11 (8)

Содержание acon

























































































































































































































Отзывы:

Нет отзывов