manualshive.com logo in svg

IAI acon, Руководство по эксплуатации, Страница: 151 / 216

Поделиться
Скачать
IAI acon Скачать руководство пользователя страница 151

3. SCON-CA

145

(2)  I/O Signal Allocation for each Axis 

The I/O signals of each axis consist of one input word (8 words = 16 bytes) and one output word in the I/O 
areas. 

z

  The control signals and status signals are ON/OFF signals in units of bit. 

z

  The target position and current position are expressed using 2-word (32 bits) binary data. The figures 

from –999999 to +999999 (Unit: 0.01mm) can be set in PLC. However, set the position data within the 
soft stroke range (0 to effective stroke length) for the actuator concerned. 

z

  Set the positioning band. The positioning band is expressed using 2-word (32 bits) binary data. The 

figures from 1 to +999999 (Unit: 0.01mm) can be set in PLC. 

z

  The specified speed is expressed using 1-word (16 bits) binary data. The figures from 0 to +65535 (Unit: 

1.0mm/sec) can be set in PLC. Set the value that does not exceed the max. speed value for the actuator 
concerned. 

z

 The Acceleration/Deceleration is expressed using 1-word (16 bits) binary data. The figures from 1 to 300 

(Unit: 0.01G) can be set in PLC. However, set the value that does not exceed the max. 
acceleration/deceleration value for the actuator in question. 

z

  The pressing current-limiting value is expressed using 1-word (16 bits) binary data. The figures from 0 

(0%) to 510 (200%) can be set in PLC. However, set the value within the settable range for the pressing 
current-limiting value (Refer to the Catalog or Operation Manual for the actuator) for the actuator 
concerned. 

Set Value 

Pressing current-limiting value 

z

  The command current is expressed using 2-word (32 bits) binary data (Unit: 1mA). 

z

  The current speed is expressed using 2-word (32 bits) binary data (Unit: 0.01mm/sec). 

z

  The alarm code is expressed using 1-word (16 bits) binary data. 

Содержание acon

























































































































































































































Отзывы:

Нет отзывов