IAI acon Скачать руководство пользователя страница 101

Страница: 101 / 216

3. SCON-CA

SCON-CA

output

PLC input Side (* “n” indicates the byte address of each axis.)

DO on the SCON-CA side and output data register

Position/Simplified

direct value mode 2

Half direct value

mode 2

Remote I/O node 3

Half direct value node 3

PLC input

area

(bytes)

Number of occupied

bytes:8

Number of

occupied bytes: 16

Number of occupied

bytes: 12

Number of occupied

bytes: 16

n+0, n+1

Port number 0 to 15

n+2, n+3

Current position

Occupied area

Current position

n+4, n+5

Completed position

number

(simple alarm ID)

n+6, n+7

Status signal

Force feedback

data

Current position

Command current

n+8, n+9

n+10, n+11

Current speed

Force feedback data

Current speed

n+12, n+13

Alarm code

n+14, n+15

Status signal

n+16, n+17
n+18, n+19
n+20, n+21
n+22, n+23
n+24, n+25
n+26, n+27
n+28, n+29
n+30, n+31

(Note) The Occupied area shows the domain to be occupied with the operation mode setting.

Therefore, this domain cannot be used for any other purpose. Also, exercise caution to avoid node
address duplication.

Содержание acon

























































































































































































































Результаты поиска

Содержание acon

Отзывы:

IAI acon, Руководство по эксплуатации, Страница: 101 / 216

Результаты поиска

Содержание acon

Отзывы: