manualshive.com logo in svg

IAI acon, Руководство по эксплуатации, Страница: 117 / 216

Поделиться
Скачать
IAI acon Скачать руководство пользователя страница 117

3. SCON-CA

111

(* “ON” in the table shows the corresponding bit of “1” and “OFF” shows “0”.) 

Signal type 

Bit 

Symbol 

Contents 

Details 

Pressing

current-limiting 

value

16-bit

data

-

16-bit integer 
Specify the current-limiting value to be used during pressing operation. 
The allowable specification range is 0 (0%) to 255 (100%). 
The actual settable range varies depending on each actuator.(Refer to 
the catalog or Operation Manual for the actuator.) If a move command is 
issued by specifying a value exceeding the maximum pressing current, 
an alarm will occur. 

3.8 (2) 

b15 

BKRL  Forced brake release: When it is turned ON, the brake is released. 

3.6.11 (18)

b14 RMOD 

Operating mode selector: The AUTO mode is selected when this signal 
is OFF, and the MANU mode is selected when the signal is ON. 

3.6.11 (19)

b13 DIR 

Pressing direction specification: 
“OFF” for the direction reducing the positioning band from the target 
position, 
“ON” for the direction adding the positioning band to the target position 

3.6.11 (22)

b12 PUSH 

Pressing specification: Positioning operation is performed when this 
signal is OFF, and pressing operation is performed when the signal is 
ON.

3.6.11 (21)

b11 GSL1 

Servo gain parameter 
set selection 1 

b10 GSL0 

Servo gain parameter 
set selection 0 

Select the servo gain parameter set to be used.

GSL1

GSL0 Function 

OFF 

OFF 

Select parameter set 0. 

OFF 

ON 

Select parameter set 1. 

ON 

OFF 

Select parameter set 2. 

ON 

ON 

Select parameter set 3. 

3.6.11 (33)

b9 

- 

Cannot be used. 

- 

b8 

JOG+  + Jog: “ON” for Movement in the Opposite Direction of Home 

3.6.11 (13)

b7 

JOG- 

-Jog: “ON” for Movement to the Home Direction 

3.6.11 (13)

b6 JVEL 

Jog-speed/inch-distance switching: 
The values set in parameter No. 26, “Jog speed” and parameter No. 48, 
“Inch distance” are used when this signal is OFF, and the values set in 
parameter No. 47, “Jog speed 2” and parameter No. 49, “Inch distance 
2” are used when the signal is ON. 

3.6.11 (14)

b5 JISL 

Jog/inch switching: 
Jog operation is performed when this signal is OFF, and inch operation 
is performed when the signal is ON. 

3.6.11 (15)

b4 

SON 

Servo ON Command: The servo turns ON when this signal turns ON. 

3.6.11 (5) 

b3 

RES 

Reset: A reset is performed when this signal turns ON. 

3.6.11 (4) 

b2 

STP 

Pause: A pause command is issued when this signal turns ON. 

3.6.11 (11)

b1 HOME 

Home return: A home-return command is issued when this signal turns 
ON.

3.6.11 (6) 

PLC output 

Control signal 

b0 DSTR 

Positioning Command: A move command is issued when this signal 
turns ON. 

3.6.11 (8) 

Содержание acon

























































































































































































































Отзывы:

Нет отзывов