manualshive.com logo in svg

IAI acon, Руководство по эксплуатации, Страница: 28 / 216

Поделиться
Скачать
IAI acon Скачать руководство пользователя страница 28

2. ACON, 

PCON

22

(3)  I/O signal assignment 

The controller's I/O port signal varies depending on the parameter No. 25 setting. 
(Refer to operation manual for the controller main body for more information.) 

 ACON  

Parameter No. 25 setting 

Positioning mode 

Teaching mode 

256-point mode 

0 1  2 

Category 

Port No. 

Signal name 

Symbol

Signal name 

Symbol

Signal name 

Symbol

0 PC1 

PC1  PC1 

1 PC2 

PC2  PC2 

2 PC4 

PC4  PC4 

3 PC8 

PC8  PC8 

4 PC16 

PC16 PC16 

5

Command position 

No.

PC32

Command position 

No.

PC32 PC32 

6 - 

Teaching mode 

command

MODE PC64 

7 - 

Jog/inching 

selector

JISL 

Command position No.

PC128

8

Unavailable 

- +Jog 

JOG+ 

Unavailable 

- 

9 

Forced brake release 

BKRL 

-Jog 

JOG- 

Forced brake release

BKRL 

10

Operating mode 

selector

RMOD

Operating mode 

selector

RMOD

Operating mode 

selector

RMOD

11 

Home return 

HOME

Home return 

HOME 

Home return 

HOME

12 Pause 

*STP 

Pause 

*STP Pause *STP 

13 Positioning 

start 

CSTR

Positioning

start/position data 

import command 

CSTR/ 
PWRT 

Positioning start 

CSTR 

14 Reset RES 

Reset RES Reset RES 

PLC output 

ACON input 

15 

Servo ON command 

SON 

Servo ON command

SON 

Servo ON command

SON 

0 PM1 

PM1  PM1 

1 PM2 

PM2  PM2 

2 PM4 

PM4  PM4 

3 PM8 

PM8  PM8 

4 PM16 

PM16 PM16 

5

Completed position 

No.

PM32

Completed position 

No.

PM32 PM32 

6 Moving 

signal 

MOVE

Moving signal 

MOVE 

PM64 

7 Zone 

1 

ZONE1

Teaching mode 

signal 

MODES

Completed position 

No.

PM128

8 

Position zone 

PZONE

Position zone PZONE

Position 

zone  PZONE

9

Operation mode 

status

RMDS

Operation mode 

status

RMDS 

Operation mode status

RMDS

10

Home return 

completion 

HEND

Home return 

completion 

HEND

Home return 

completion 

HEND

11

Positioning

completion signal 

PEND

Positioning

completion signal/
position-data read 

complete

PEND/
WEND

Positioning completion 

signal 

PEND

12

Operation 

preparation end 

SV

Operation 

preparation end 

SV

Operation preparation 

end

SV

13 

Emergency stop 

*EMGS

Emergency stop 

*EMGS

Emergency stop 

*EMGS

14 Alarm 

*ALM 

Alarm 

*ALM Alarm *ALM 

ACON output 

PLC input 

15 Unavailable  -  Unavailable  -  Unavailable  - 

The symbol with a * mark shows the ON signal in normal condition. 
The signal described as “Unavailable” is not controlled. (ON/OFF is undefined.) 

Содержание acon

























































































































































































































Отзывы:

Нет отзывов