IAI acon Скачать руководство пользователя страница 98

Страница: 98 / 216

3. SCON-CA

3.6

Communicating with the Master Station

3.6.1

Operation Modes and Corresponding PLC I/O Areas

The channels allocated for each operation mode are described as follows.

PLC

output

SCON-CA input (* “n” indicates the byte address of each axis.)

DI on the SCON-CA side and input data register

Remote I/O

mode

Position/

Simplified direct

value mode

Half direct value

mode

Full direct value

mode

Remote I/O

mode 2

PLC output

area (bytes)

Number of

occupied bytes:

Number of

occupied bytes:

Number of

occupied bytes:

Number of

occupied bytes:

Number of

occupied bytes:

n+0, n+1

Port No.0 to 15

n+2, n+3

Target position

n+4, n+5

Specified

position number

n+6, n+7

Control signal

Positioning band

n+8, n+9

Speed

n+10, n+11

Acceleration/

Deceleration

Speed setup

Occupied area

n+12, n+13

Pressing

current-limiting

value

n+14, n+15

Control signal

Zone b

n+16, n+17

n+18, n+19

Zone boundary-

n+20, n+21

Acceleration

n+22, n+23

Deceleration

n+24, n+25

Pressing

current-limiting

value

n+26, n+27

Load current

threshold

n+28, n+29

Control signal 1

n+30, n+31

Control signal 2

(Note) The Occupied area shows the domain to be occupied with the operation mode setting.

Therefore, this domain cannot be used for any other purpose. Also, exercise caution to avoid node
address duplication.

Содержание acon

























































































































































































































Результаты поиска

Содержание acon

Отзывы:

IAI acon, Руководство по эксплуатации, Страница: 98 / 216

Результаты поиска

Содержание acon

Отзывы: