manualshive.com logo in svg

IAI acon, Руководство по эксплуатации, Страница: 9 / 216

Поделиться
Скачать
IAI acon Скачать руководство пользователя страница 9

3

No.

Operation 

Description 

Description 

(3) Grounding 
  Make sure to perform the grounding of type D (Former Type 3) for the controller. 

The grounding operation should be performed to prevent an electric shock or 
electrostatic charge, enhance the noise-resistance ability and control the 
unnecessary electromagnetic radiation. 

4 Installation 

and 

Start

(4) Safety Measures 
  When the work is carried out with 2 or more persons, make it clear who is to be 

the leader and who to be the follower(s) and communicate well with each other to 
ensure the safety of the workers. 

  When the product is under operation or in the ready mode, take the safety 

measures (such as the installation of safety and protection fence) so that nobody 
can enter the area within the robot’s movable range. When the robot under 
operation is touched, it may result in death or serious injury. 

  Make sure to install the emergency stop circuit so that the unit can be stopped 

immediately in an emergency during the unit operation. 

  Take the safety measure not to start up the unit only with the power turning ON. 

Failure to do so may start up the machine suddenly and cause an injury or 
damage to the product. 

  Take the safety measure not to start up the machine only with the emergency stop 

cancellation or recovery after the power failure. Failure to do so may result in an 
electric shock or injury due to unexpected power input. 

  When the installation or adjustment operation is to be performed, give clear 

warnings such as “Under Operation; Do not turn ON the power!” etc. Sudden 
power input may cause an electric shock or injury. 

  Take the measure so that the work part is not dropped in power failure or 

emergency stop. 

  Wear protection gloves, goggle or safety shoes, as necessary, to secure safety. 
  Do not insert a finger or object in the openings in the product. Failure to do so may 

cause an injury, electric shock, damage to the product or fire. 

  When releasing the brake on a vertically oriented actuator, exercise precaution not 

to pinch your hand or damage the work parts with the actuator dropped by gravity. 

Содержание acon

























































































































































































































Отзывы:

Нет отзывов