HydraMaster Steamatic 8800 TMU Скачать руководство пользователя | Manualshive

Страница: 36 / 148

background image

Cleaning Information

-

3-4

Steamatic 8800 TMU

CleanIng tool tIpS

Wands

With a wand, keep cleaning strokes short, front to back, and run a “dry pass”.

After pulling the wand for a strip of 3 or 4 ft (0.9 m or 1.2 m) long with the solution trigger
activated, go back up to the top of the stroke, and make a “dry “ pass [i.e. no solution

flowing]. This gives the wand a second chance to pick up the solution on the carpet.

If you do not run a dry pass, the carpet can take longer to dry, and, possibly, the pad under
the carpet can become saturated.

be aware of the carpet seams; try to use strokes that are parallel with the seam. Avoid
pulling the want across the seam. every stroke can peel the seam connection and pull

the carpet off the floor.

Also, tilt the wand handle down [head up] to move the tool forward, and away from you,
on the carpet. This means less pull on the carpet and less work for you.

«
...
34
35
36
37
38
...
»

Содержание Steamatic 8800 TMU





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Steamatic 8800 TMU

Бренд: Bacharach Страницы: 48

Бренд: dbx Страницы: 12

Бренд: dbx Страницы: 13

Бренд: dbx Страницы: 72

Бренд: dbx Страницы: 11

Бренд: dbx Страницы: 16

Бренд: ICELED Страницы: 4

Бренд: Facom Страницы: 4

Бренд: FaceLake Страницы: 2

Бренд: Major Страницы: 52

Бренд: Park House Healthcare Страницы: 12

Бренд: ValueStore US Страницы: 2

Monolith NT.115

Бренд: Nano Temper Страницы: 24

SCAFFOLDBENCH I-CISRL

Бренд: MetalTech Страницы: 16

Бренд: SDE Lighting Страницы: 7

Бренд: impact Страницы: 8

Бренд: TOTAL10 Страницы: 16

Бренд: Icom Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды